Black cartridge error - Lexmark X4650 InkJet Printer

Hi there

You should always mention the printer model as well as what operating system you use.

This is what i found on LEXMARK's website about your error, and it seems you have one or 2 faulty cartridges, or you are using compatible cartridges instead of Lexmark Originals:

Problem Error messages; Error: "Cartridge Error 50C"; Cartridge error; Black cartridge missing; Color cartridge missing Solution Cartridge Error 50C
Your print cartridge has shorted.

1. Power off your All-in-One and unplug it.


2. Plug in your All-in-One again and turn it on.


3. Uninstall and then reinstall your cartridges.


4. If this does not resolve the issue, try the troubleshooting steps for the other cartridge errors below.
   

Error: Black Cartridge Missing
The black cartridge is not installed. (Install cartridge PN 82)
Error: Color Cartridge Missing
The color cartridge is not installed (Install cartridge PN 83)
Cartridge Error
Complete the following instructions:

1. Power off your All-in-One.


2. Use both hands to lift up the scanner unit until the scanner support holds it open.


3. Turn the All-in-One on. The print cartridge carrier moves and stops at the loading position, unless the All-in-One is busy.


4. Remove the color print cartridge.


5. Lower the scanner unit until it is completely closed.


6. If the error message reappears, replace the black print cartridge with a new print cartridge.
   If it does not repeat steps 1-3 and then go to step 7.


7. Reinstall the color cartridge and remove the black print cartridge.


8. Lower the scanner unit until it is completely closed.


9. If the error message occurs again, replace the color cartridge.


10. If an error message reappears, repeat steps 1-3 and reinstall both print cartridges.


11. Lower the scanner unit until it is completely closed.


12. If you receive the error message again, replace both cartridges.

Hope it helps

Andre

10.1000 Black e-label missing error Error message 10.1000 supply error alternates with Reinstall with a ? under the Black print cartridge gas gauge Description The black print cartridge or print cartridge e-label is missing. Action

1. Install the black print cartridge.

NOTE: If this error occurs upon initial power-up on the printer, remove all cartridges to check for the orange packing tape. If present, remove it before reinstalling the toners.

Error messages; Error: "Cartridge Error 50C"; Cartridge error; Black cartridge missing; Color cartridge missing Solution Cartridge Error 50C
Your print cartridge has shorted.

1. Power off your All-in-One and unplug it.
   
2. Plug in your All-in-One again and turn it on.
   
3. Uninstall and then reinstall your cartridges.
   
4. If this does not resolve the issue, try the troubleshooting steps for the other cartridge errors below.
   

Error: Black Cartridge Missing
The black cartridge is not installed. (Install cartridge PN 82)
Error: Color Cartridge Missing
The color cartridge is not installed (Install cartridge PN 83)
Cartridge Error
Complete the following instructions:

1. Power off your All-in-One.
   
2. Use both hands to lift up the scanner unit until the scanner support holds it open.
   
3. Turn the All-in-One on. The print cartridge carrier moves and stops at the loading position, unless the All-in-One is busy.
   
4. Remove the color print cartridge.
   
5. Lower the scanner unit until it is completely closed.
   
6. If the error message reappears, replace the black print cartridge with a new print cartridge.
   If it does not repeat steps 1-3 and then go to step 7.
   
7. Reinstall the color cartridge and remove the black print cartridge.
   
8. Lower the scanner unit until it is completely closed.
   
9. If the error message occurs again, replace the color cartridge.
   
10. If an error message reappears, repeat steps 1-3 and reinstall both print cartridges.
    
11. Lower the scanner unit until it is completely closed.
    
12. If you receive the error message again, replace both cartridges.

Hi there Error 50c

Can only gave it a try.

Regarding the Dell A940 "Error 50c"....the user guide doesn't seem to mention "Error 50c". They do, however, mention a "Cartridge Error" on page 52 of the manual. They claim this means that the printer has detected a short circuit (fuse/resister) in the cartridge. As you may or may not have noticed in the manual, this is what they recommend doing about it:

1) Press Power to turn the printer off.

2) Lift the printer cover/lid (scanner unit) until the scanner support holds it open.

3) Turn the printer on.
The ink cartridge carrier moves and stops at the loading position unless the printer is busy.

4) Remove the color ink cartridge.

5) Lower the printer (scanner unit) until it is completely closed.
If the error message displays again, replace the black cartridge with a new black cartridge.

If the error message does not display, repeat steps 1–3 and then go to step 6.

6) Reinstall the color cartridge and remove the black ink cartridge.

7) Lower the printer (scanner unit) until it is completely closed.

If the error message displays again, replace the color cartridge with a new
color cartridge.
If there is no error message (indicated by flashing lights), repeat steps 1–3 and then reinstall both ink cartridges.
8) Lower the printer (scanner unit) until it is completely closed.

If you get the error message again, while both cartridges are installed, replace both of the cartridges.

Basically, what they want you to determine is,....if the short circuit is with the "black ink" cartridge or the "color ink" cartridge and then replace the cartridge that has the problem.

You may have to buy a new cartrige.
Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

hi there,

you can try these steps:

try to remove the new black cartridge. get a clean cloth. gently wipe the copper strip of the cartridge. unplug the power cable of the printer. gently wipe the contacts of the black cartridge carrier (where you put the black cartridge in). close the carrier, plug the power cable back in. install the black cartridge. then check for the error code.
if you still have same error code, try the old cartridge.
if the old cartridge still works, you need to contact dell for the replacement of the black cartridge (if you purchase the black cartridge from dell)
if the old cartridge is also giving same error. try the steps on the color cartridge as well, it might be with the color cartridge error.
or both.
worst case scenario the contacts on the printer carrier might be broken already.
but in this kind of situation. 98% it's the cartridge that's causing the issue.

have a great day :)

Cartridge Error 50C
Your print cartridge has shorted.

1. Power off your All-in-One and unplug it.
2. Plug in your All-in-One again and turn it on.
3. Uninstall and then reinstall your cartridges.
4. If this does not resolve the issue, try the troubleshooting steps for the other cartridge errors below.
   

Error: Black Cartridge Missing
The black cartridge is not installed. (Install cartridge PN 82)

Error: Color Cartridge Missing
The color cartridge is not installed (Install cartridge PN 83)


Cartridge Error
Complete the following instructions:

1. Power off your All-in-One.
2. Use both hands to lift up the scanner unit until the scanner support holds it open.
3. Turn the All-in-One on. The print cartridge carrier moves and stops at the loading position, unless the All-in-One is busy.
4. Remove the color print cartridge.
5. Lower the scanner unit until it is completely closed.
6. If the error message reappears, replace the black print cartridge with a new print cartridge.
   If it does not repeat steps 1-3 and then go to step 7.
7. Reinstall the color cartridge and remove the black print cartridge.
8. Lower the scanner unit until it is completely closed.
9. If the error message occurs again, replace the color cartridge.
10. If an error message reappears, repeat steps 1-3 and reinstall both print cartridges.
11. Lower the scanner unit until it is completely closed.
12. If you receive the error message again, replace both cartridges.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Hi there Error 50c

Dell gets this lots so have a try.

Regarding the Dell A940 "Error 50c"....the user guide doesn't seem to mention "Error 50c". They do, however, mention a "Cartridge Error" on page 52 of the manual. They claim this means that the printer has detected a short circuit (fuse/resister) in the cartridge. As you may or may not have noticed in the manual, this is what they recommend doing about it:

1) Press Power to turn the printer off.

2) Lift the printer cover/lid (scanner unit) until the scanner support holds it open.

3) Turn the printer on.
The ink cartridge carrier moves and stops at the loading position unless the printer is busy.

4) Remove the color ink cartridge.

5) Lower the printer (scanner unit) until it is completely closed.
If the error message displays again, replace the black cartridge with a new black cartridge.

If the error message does not display, repeat steps 1–3 and then go to step 6.

6) Reinstall the color cartridge and remove the black ink cartridge.

7) Lower the printer (scanner unit) until it is completely closed.

If the error message displays again, replace the color cartridge with a new
color cartridge.
If there is no error message (indicated by flashing lights), repeat steps 1–3 and then reinstall both ink cartridges.
8) Lower the printer (scanner unit) until it is completely closed.

If you get the error message again, while both cartridges are installed, replace both of the cartridges.

Basically, what they want you to determine is,....if the short circuit is with the "black ink" cartridge or the "color ink" cartridge and then replace the cartridge that has the problem.

You may have to buy a new cartrige.
Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

There is a problem with one of the cartridges.

What you nee to do is first remove the cartridges and close the carrier lids. Unplug the printer from the electrical outlet, wait a few seconds, then plug it in again. If the power button isn't lit, turn on the power. Reinsert the printer cartridges, and you should be good to go.

If you see the error again, then repeat the above procedure and only put in the black cartridge instead of both. If you don't get the error, then try putting in the photo cartridge. This will let you know which cartridge has the problem. If the black alone causes the error, the black one is the problem. If you see the error when you insert both, but not with the black, then the photo cartridge is the bad one. Get a new cartridge (either black or photo) and that should take care of the issue.

Is that an error code "Cartridge Error 50C" ? If so, see below....

Cartridge Error 50C: Your print cartridge has shorted.
1. Power off your All-in-One and unplug it.
2. Plug in your All-in-One again and turn it on.
3. Uninstall and then reinstall your cartridges.
4. If this does not resolve the issue, try the troubleshooting steps for the other cartridge errors below.

Error: Black Cartridge Missing - The black cartridge is not installed. (Install cartridge PN 82)
Error: Color Cartridge Missing - The color cartridge is not installed (Install cartridge PN 83)

Cartridge Error: Complete the following instructions:
1. Power off your All-in-One.
2. Use both hands to lift up the scanner unit until the scanner support holds it open.
3. Turn the All-in-One on. The print cartridge carrier moves and stops at the loading position, unless the All-in-One is busy.
4. Remove the color print cartridge.
5. Lower the scanner unit until it is completely closed.
6. If the error message reappears, replace the black print cartridge with a new print cartridge.
If it does not repeat steps 1-3 and then go to step 7.
7. Reinstall the color cartridge and remove the black print cartridge.
8. Lower the scanner unit until it is completely closed.
9. If the error message occurs again, replace the color cartridge.
10. If an error message reappears, repeat steps 1-3 and reinstall both print cartridges.
11. Lower the scanner unit until it is completely closed.
12. If you receive the error message again, replace both cartridges.

How I solved this problem was, I took out the color cartridge (which seem to be the one giving the error message) and worked only with the black ink (and chose print black and white )

My color ink cartridge had been refilled at Walgreens. The Black ink cartridge is an original Lexmark