Washer filled with water then stopped. Tried to do the lid switch and wasn't it. Dont know what to do now. Any help would be greatly appreciated.

Question edited for typos.

Sounds as if the switch was wired wrong.

https://www.google.com/search?q=Roper+washer+model+RAS8445KQ0+replace+lid+switch

..

Use a shop vac to get the water out after the clothing is removed. These links should help:

How to Replace the Lid Switch Lock Assembly on Top Load Washer Repair... Washer Lid Switch Part Number 3949238 GUARANTEED FIT from Sears PartsDirect Kenmore 80 Series Washer Lid Switch Repair won drain or spin
Whirlpool washer stopped working full of water and clothes after opening...

From the closed position lift the lid of the washer about 2'' and listen for a distinct click. Then set lid back down and should hear another click just before it closes. The wire form hinge on left side of lid actuates the lid switch. Is it broken? Let me know.

see this causes and fix it. God bless you
Lid Switch Assembly If the washer stops mid cycle the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design
Door Lock Motor and Switch Assembly If the washer stops mid cycle the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.
Water Inlet Valve If the washer stops mid cycle the water inlet valve cold water side may have failed. Most washers have a cold water rinse and so if they can't fill with cold water they just sit indefinitely waiting for the cold water to enter. If there is cold water to the water inlet valve and the cold water works in other parts of the cycle - or to make warm water - the valve is not the problem.

Main Control Board If the washer stops mid-cycle the main control board might be defective. This is not common. Check other causes first such as the lid or door switch and other components.

Timer If the washer stops mid cycle the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.

Hello, welcome to FixYa.

The scenario you describe is usually associated with a faulty or broke lid switch...but I don't know if you checked that yet or if you know how.

The lid switch failure is definitely a common top load washer problem. Here`s how you can repair it pretty easily...

( this is based on the most common Whirlpool, Estate, Kitchen-Aid, Roper, Kenmore, Inglis top-load washer, not necessarily applicable to ALL...but with a model number I could say if it cover's yours)

Here`s a helpful link for changing it out,

http://videos.wittysparks.com/id/3098139337

The lid switch will look like this...


or this...depending of course on the model,


Let me know how you make out. If this is something you think is not within' your scope of expertise please call a pro. I think you'll be fine with the tutorial video'

I will try to help in any manner I can of course as well. Good luck.

Thank you for choosing FixYa. Please take a moment to rate the info I provided and a short testimony is appreciated.

Regards,

Macmarkus :)

Hello, Welcome to FixYa. The scenario you describe is usually associated with a faulty or broke lid switch...but I don't know if you checked that yet or if you know how.
The lid switch failure is definitely a common top load washer problem. Here`s how you can repair it pretty easily...

( this is based on the most common Whirlpool, Estate, Kitchen-Aid, Roper, Kenmore, Inglis top-load washer, not necessarily applicable to ALL...but it should cover yours)

Here`s a helpful link for changing it out,

http://videos.wittysparks.com/id/3098139337

The lid switch will look like this...


Let me know how you make out. If this is something you think is not within' your scope of expertise please call a pro. I think you'll be fine with the tutorial video'

I will try to help in any manner I can of course as well. Good luck.

Thank you for choosing FixYa. Please take a moment to rate the info I provided and a short testimony is appreciated.

Regards,

Macmarkus :)

Hello, Welcome to FixYa. The scenario you describe is usually associated with a faulty or broke lid switch...but I don't know if you checked that yet or if you know how.
The lid switch failure is definately a common top load washer problem. Here`s how you can repair it pretty easily...

( this is based on the most common Whirlpool, Estate, Kitchen-Aid, Roper, Kenmore, Inglis top-load washer, not necessarily applicable to ALL...but it should cover yours)

Here`s a helpful link for changing it out,

http://videos.wittysparks.com/id/3098139337

The lid switch will look like this...


Let me know how you make out. If this is something you think is not within' your scope of expertise please call a pro. I think you'll be fine with the tutorial video'

I will try to help in any manner I can of course as well. Good luck.

Thank you for choosing FixYa. Please take a moment to rate the info I provided and a short testimony is appreciated.

Regards,

Macmarkus :)

id check the brushes on the motor first..........if there goosed the machine will not go past filling with water.........

cheers

This switch is a safety switch and needs to be working properly.

The condition that you describe sounds like the switch is not indicating the lid is closed...so no spin.

Also, check that both hot and cold fill hoses are on, <<Be sure.

Doc

The timer is failed in this case.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question