SCSI board BJW 9000

Hi there
I have found some details of the printer here
http://pdf.textfiles.com/manuals/STARINMANUALS/Sony%20Security/UP-D50%20-%20Quick%20Spec.pdf
where it clearly states that the printer is SCSI based. This is not a usual printer interface, and it is highly unlikely that your Vaio will have a SCSI interface at all. However it does say "USB compatible with optional SCSI to USB converter cable" with a footnote "Window 2000/XP only" and your Vaio will almost certainly have a USB interface. Unfortunately the drivers on the Sony website here:
Sony Global DP UP D50
only go up to Windows 2000/XP with no drivers listed for later versions of Windows, so you may have problems getting a driver to work.
But I think your major problem will be getting the cable to link the two. Sony's web site doesn't come up with anything and more general searches don't come up with a lot. My best suggestion is to determine the type of SCSI plug/socket on the printer and then go for an external SCSI adaptor (USB) with the appropriate plug/socket and then use an appropriate SCSI to SCSI cable to link the two. Without knowing more about your Sony's SCSI interface type I'm afraid I can't help more.
Hope this has been a little helpful
Cheers

Hello,

First, a power adapter is required to connect your scanner. the power adapter must be supplied with the scanner. If your scanjet 5470c scanner is having USB interface or connectivity, then you need USB cable and if it is SCSI interface, then you need SCSi cable to connect to your PC. The cables are usually be supplied with the scanner. If lost, you may have purchase teh same. For further assistance, please visit the following link:

http://h20000.www2.hp.com/bizsupport/TechSupport/SupportTaskIndex.jsp?lang=en&cc=us&prodTypeId=15179&prodSeriesId=28456&taskId=115

Hope the above information is helpful.

Thanks,
ScanCare

I have the bjw 9000 manuel on my desk top

email me at [email protected] and i will send you a copy
Tony

SCSI- Small Computer System Interface

It is a set of standards for physically connecting and transferring data between computers and peripheral devices.

I think this is the one you are looking for: http://www.korg.com/SupportResults.aspx?productid=461 or http://www.korg.com/SupportResults.aspx?search=triton

Usually, SCSI devices come with the termination built into the device. Older devices actually had two or three terminating resistor packs plugged into the card or drive circuit board. More modern ones have DIP switches to turn the termination on or off.
Essentially, on a SCSI daisy chain ribbon cable with multiple connectors, only the first and last physical device needs to be terminated. Usually SCSI devices come from the factory already terminated. If you have only one device to connect check and see if there is a DIP switch to change. I would go ahead and connect it. If it works, it's probably already set properly.
That said, I have worked with daisy chains of SCSI devices where a particular device would only work if it were terminated even if it was in the middle of the chain. s

The BJW 9000 manuel is available as a free download I have downloaded it my self but dont have it at home why not do the same
Tony (withtrader)
best of luck

Are you using a Kofax SCSI card or an normal SCSI controller like Adaptec?
By using a normal SCSI controller, is there an ASPI driver problem after a WIN XP update? After an update check the ASPI dlls in \sytem32. They should be version 4.71 or higher.

Check the SCSI connector pins and the terminator.
If available change the cable.

Scanner check:
Is the green lamp (Ready) on or is the red lamp (Error) on?

- green lamp on:
the internal self test is ok, but the internal SCSI interface may possibly faulty.

- red lamp on:
the internal selftest detect an error.
It's possible that the DC/DC power board, the CPU board or the power supply inside the scanner is defective.
After reassembling the front side camera you will see at the bottom a PCA board with some LEDs whitch indicate by red light the different voltages when power is on. You find the different voltages printed at the PCA close to the LEDs.
In case on or more LEDs don't shine the according DC/DC transformer on the PCA is defective.
Futher you see LEDs at the camera PCAs. They should be on too.

In case the CPU board has an defect you must have an special Kodak activation tool to unlock an new or used CPU board after exchange.

That thing required a SCSI terminator pack doesn't it.

If so, is it working properly.

I've had those things go out on me before leaving me to pull my hair out many times.

perhaps this will help. I ran across it by accident
http://home.netcom.com/~agia/cable.jpg
good luck
Mike