Toys Logo

Related Topics:

Posted on Jan 08, 2009

How to open FP music box record player, #995 or #995N

If I can remove the 4 hex screws, how do I open FP music box record player, #995 or #995N

5 Answers

Anonymous

Level 1:

An expert who has achieved level 1.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 1 Answer
  • Posted on Jan 18, 2009
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Jan 18, 2009
Answers
1
Questions
0
Helped
5391
Points
18

Fisher Price Music box: to open, remove the four screws from the bottom, open the two parts as wide as possible without using too much force. Using a small flat blade screw driver, insert between the red cover and white top where the wind up knob is located. Pry the red bottom out far enough to allow the ring surrounding the knob to slide under the red bottom. The box is now open.

After repair, and re-assembling, make sure the wider part of the wind up stop wheel faces the front of the player, otherwise the wind up knob catches and slows the mechanism.

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 1 Answer
  • Posted on Jun 02, 2010
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Jun 02, 2010
Answers
1
Questions
0
Helped
5391
Points
8

When you have taken the case off, if it is running slowly then some WD40 works very well in the clockwork mechanism. Also WD40 the head of the arm. The xylophone in the head is very fiddly to adjust but persevere and once again our 37year old's record player is ready for the grand-children

Ad

Anonymous

Level 1:

An expert who has achieved level 1.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 3 Answers
  • Posted on Jan 16, 2009
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Jan 16, 2009
Answers
3
Questions
0
Helped
5558
Points
14

It just pulls apart, but with a little difficulty because the music box fits in quite snugly. And when it does come apart, surprise - the pieces fall out leaving hardly a clue where they belong. Try to peak in while prying it slightly to note where they go. The parts that fall out include a yellow winder button, a red casing around it (both visible from the outside), and a yellow spoked wheel that rides on the side of the winder button to prevent overwinding. Make sure you try it out completely before reassembling so you don't have to take it apart again to turn something around or reset the spoked wheel. It snaps together a little easier than it comes apart.

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

  • Contributor 1 Answer
  • Posted on Mar 23, 2011
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Joined: Mar 23, 2011
Answers
1
Questions
0
Helped
5391
Points
1

Remove 4 screws. Pry open about 1/4 inch, just enough to insert red straw attached to your WD40 nozzle. Lubricate metal parts inside near the stem of the yellow wind-up knob. Lubricate metal wheels under the armature. That did the job for us! Player seems to operate at normal speed.

Philippe Leroy

Level 1:

An expert who has achieved level 1.

  • Contributor 1 Answer
  • Posted on Nov 22, 2019
Philippe Leroy
Contributor
Level 1:

An expert who has achieved level 1.

Joined: Nov 22, 2019
Answers
1
Questions
0
Helped
5391
Points
1

Il y a une cinqui?me vis dans le bo?tier ? piles !
?tez les 3 piles et vous verrez appara?tre cette cinqui?me vis de fixation.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

5helpful
1answer

How to change cabin filter 2011 Lacrosse

I just changed mine yesterday and these tips listed above were unfortunately incorrect.

Step 1 - Open the passenger door
There is a panel that has no screws on the flatside of the dashboard which faces against the closed door at the jam side. Use a body tool and pry the panel carefully exposing the inside area of the glovebox. If possible dont do this in cold weather because the tabs are plastic. Inside the panel you will see one small tab that the glove box has a 1/4 plastic clip seated in the tab.

Step 2 - Open the glove box. Remove the 3 hex screws on the top interior row of the glove box.

Step 3 - At the right and left corners of the bottom of the glove box remove the two front facing screws on the lower hinge.

Step 4- At the very bottom parallel to the floor there are two more hex screws remove those (they hold the plastic vent in place underneath the glove box. Pull the vent downward to release the tabs.
IMPORTANT: Dont forget to go back to step 1 and pull the small tab from the slot in the dashboard cover area ( Inside the panel you will see one small tab that the glove box has a 1/4 plastic clip seated in the tab)

Step 5 - Pull down on the glove box to release the clips.

Step 6 - You will see a black box inside. There are three tabs (right, top, and left) pull them individually to remove the front facing cover. Inside you will see the air filter. Remove and have airflow arrow pointed downward.

Reverse steps to reinstall. Be sure to line up the clips before pressing them back in place. Do not force them!

Good luck. I hope this helps. I did mine on the first attempt with no issues in about 10 minutes (I'm not a mechanic).
0helpful
1answer

How to open Harman Kardon Go Play

there's as hex screw in the battery compartment
10helpful
1answer

Battery has died how do I replace it?

quiet easy, but anyhow, now warrenty whatsoever!

you need:
a) one hex screwdirver size 5mm
b) 1 phillips screwdriver size 2
c) 1 replacement battery, maintenance free lead battery block, 123V 7.0AH Type 1270
d) some pieces of 1mm thick foam rubber (4 Strips 150mm, 4 strips 65 mm and 4 strips 95mm, 8-10mm wide would be original, but quiet anything would do it)
e) some glue
f) depending on your expertnes, 20 to 40 minutes time.
... yes thats all.

here we go

DISASSEMBLY
1. lay the unit on to back
2. unscrew the edge plates on the front side (4 pieces, 3 screws each, hex)
3. remove the three edge protectors
4. unscrew the front panel (8 screws, phillips)
5. pull the frontpanel gently up by 2 cm (aprox 1 inch), will be enough
6. lift the grill without bending and remove it
7. unscrew the main speaker (4 screws, phillips)
8. carefully lift up the main speaker
9. look thru the hole, you will see the battery, mounted by 4 screws (phillips again). Unscrew
10. unplig 2 battery leads
11. lift out te battery

ASSEMBLY

1. glue some of the foam rubber arround the new battery, take tie old battery as sample.
2. slide in the battery
3. connect the leads to the battery, the red goese to te red marked pole. Importand
4. Mount the battery holder 4 screws phillips
5. slied in the speaker, mout it wit 4 screws, phillips
6. mount the grill without bending
7. siled the frontpanel back into position and screw ist (8 screws, phillips)
8. bring the edge protectors back into position
9. Mount the edge plates (3 hex screws each)
10. put it back on the weels and load your battery. Testrun.
11. have a beer for me and enyou your music.
0helpful
1answer

How do you repair a FP Music Box Record Player. I don't know how old this is, but my kids were little in the 1980's and 90's. It still works but not as fast as it should and the teeth that make the music...

my grandsons broke their mother's (and aunts') FP music box.
There was almost no sound
The teeth are simply a wind-up music box set, connected to a rod that transmits the vibrations to the diaphragm under the pseudo-tone-arm. I was able to fix by placing a cotter-pin on the rod in the arm at or near the junction and then trim with wire cutters to the correct size.
I checked the diaphragm first by tapping it through the arm/table connection.
1helpful
1answer

Fisher Price Music Box Record Player #995 What size are the hex screws and what should I use to take them out?

I'm not sure what size the hex screws are, but it's a very narrow walled socket or nut driver that you'll need. There's a place online that will sell you the exact tool for $17 or so. Don't waste your money. To do this job, you'll need a few of the clear Bic pens and a candle. Take the ink part out of the pen, then slightly melt the end with the colored cap. Quickly stick the melted end down the hole with the screw. Press hard, then let the melted plastic cool. Then, turn the hex screw. It took me a couple of times to make it work, but it does work, and I didn't have to buy a special tool.
Dec 24, 2010 • Toys
22helpful
2answers

How to change front blower motor in a 2003 dodge caravan

Removal & Installation
CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the blower motor assembly. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.

  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel
d6b70fa.gif
The blower motor is located behind the glovebox, behind the blower motor cover

  1. Remove the A/C-heater blower motor cover.
  2. Disconnect the blower motor wiring connector.
  3. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  4. Remove the blower motor mounting screws.
0e0729c.gif
Once the cover is removed, unplug the electrical connector and push it through the opening in the housing

1ed158c.gif
The blower motor is secured to the housing with three small screws

  1. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.
0helpful
2answers

How to put music on the player, wont connect to computer some reason

first of all, it depends on what mp3 player it is. but there is an obvious first step to ANY of them.
1) do you have it connected to the computer via usb?

Now that we are past the obvious, Here are a couple various solutions based on type of mp3 player it could be:
IPOD:

1) Download Itunes from www.apple.com
2) Install Itunes onto your computer.
3) Once it is installed, connect your Ipod to the computer, and it should register in itunes. Here, you can click on it, and go to your music.
4) Open a separate window with your music folder, and drag files from that window, to the Music area of Itunes. This is easy.
5) when you have all the music you want on your Ipod in the music list, press "synch". It will all go onto your ipod. and

Voila! you have music!!

Sansa:
1) forget rhapsody. its ****, ignore it, ditch it, it will charge you, and you cant even make playlists with it!!!
2) Open Windows Media Player
3) Open your music folder in a separate window
4) Drag and drop songs you want into a windows media player playlist.
5) Synch playlist to sansa.

OR

1) Still forget about rhapsody, it sucks.
2) Go to My Computer
3) Click on Removable Storage device (you should already have it plugged in at this point. the removable storage is said mp3 player)
4) Open a separate window with your music in it.
5) Drag and drop music files from your music folder into the removable storage disk. you wont be able to make playlists this way, but its easier.

Now almost any other mp3 player would work with one of these methods, possibly only with deviance in which program you will use. I hope this was of use to you.
0helpful
1answer

Broken on-off switch on Rio 600

They are Hex head screws. You need a small (1.3MM or .050) Hex head bit or Allen wrench. After removing the two screws the case will split. However the problem I'm having is figuring out how to re-attach the switch. It's a very odd connection.
Not finding what you are looking for?

5,401 views

Ask a Question

Usually answered in minutes!

Top Fisher Price Toys Experts

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66949 Answers

Jennifer Rock
Jennifer Rock

Level 2 Expert

153 Answers

NOEL
NOEL

Level 3 Expert

8606 Answers

Are you a Fisher Price Toy Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...