Parts I have a Texas Instrument Triad 810 dot matrix printer and the carrier cable is frayed and needs to be replaced. Is there a parts manual availble for this machine?

keopsj Apr 14, 2009

the head carrier cabel is broken, nned one to replace.-

1 Answer

Stone Systems International, Inc.

Contributor 5 Answers
Posted on Jul 16, 2012

Stone Systems International, Inc.

Contributor

Joined: Jul 16, 2012

Answers

Questions

Helped

2530

Points

Stone Systems $55.00 - 1-3 day lead time - Call: 1-800-289-9973

Ask for Rob Stone

2 Related Answers

Anonymous

6966 Answers
Posted on Oct 08, 2007

SOURCE: windows xp printer install

Hi, Have you tried the Epson driver "ep10759.exe"? It is available at http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?BV_UseBVCookie=yes&oid=14250&prodoid=8192&infoType=Downloads&platform=Windows It this still doesn't workout for you, pls post back as to how you connect the 810 to your PC (USB or LPT/Parallel), Good luck and kind regards.

LX 810 Impact Printer

epson.com

This link provides access to Drivers...

Desmond Pillay

40 Answers
Posted on Dec 31, 2007

SOURCE: TI 810 Blowing F2 fuse

Try Changing the bridge rectifier near the transformer.
Dezzi

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

2answers

Printer dot matrix epson dfx 9000

Wonder if it needs oil on its moving parts like to bar it travels back and forth . try a small amount of machine oil on a tissue and rub tissue on bar

Read full answer

Oct 15, 2015 • Office Equipment & Supplies

0helpful

1answer

Print head lowest pin not working

The printhead is probably bad. You can check the cable for complete insertion, unusual wear or physical cuts. There are 2 nuts on either side that attach the head to the carrage. Remove these and you can remove the printhead. There are little coils and hammers that strike the wires. Look at those for burns, misalignment or the wires being broken or too short.
Replace the printhead if necessary.

Read full answer

Apr 02, 2014 • Texas Instruments TI 810 Matrix Printer

0helpful

1answer

MY TI-810 PRINTER TRIPS THE PAPER OUT RESET AND TRERE IS PAPER IN THE PRINTER. THE PAPER OUT MICRO SWITCH HAS CONTINUNITY.

The paper out switch is on the left behind the paper. It is loose or has gotten bent. Tighten the screws or bend the lever out towards you a little and reinsert the paper.

Read full answer

Jan 18, 2014 • Texas Instruments TI 810 Matrix Printer

0helpful

1answer

I am looking for a Parts Manual for the SP300 printer and where I can order the part.\r\nI am looking for head carriage assembly, the drive pin is broke and the head just stays in one place. The head can...

hello,
http://www.devicemanuals.com/guide/Printers/Star%20Micronics/Star-Micronics-SP300-Dot-Matrix-Programmer's-TlRVMk5qYz.html
try it..
mastergani

Read full answer

Dec 03, 2010 • Star Micronics SP300 Matrix Printer

1helpful

2answers

My TI 810 printer has begun to error out. It prints a few lines, and the lines appear to "slide" to the left, until it is printing off the left edge of the paper, and then it stops printing, and the error...

Hello.
This is a ribbon problem, it needs to be changed. The fact that the lines "slide" to the left prove that the carrier is not going back to its original position every time.
So, the solution is to change the ribbon.

Read full answer

Aug 24, 2010 • Texas Instruments TI 810 Matrix Printer

0helpful

1answer