Setting radio stations on clarion auto dbr2475 w magi-tune

Recommend contacting a local car audio professional or Clarion customer support directly here:

https://clarion.com/xe/en/user-support/inquiry/contactus

Hi,

Here is the link to the owners manual which you can download if you wish:

http://owner.ford.com/servlet/ContentServer?pagename=Owner/Page/OwnerGuidePage&year=1996&make=Lincoln&model=Continental

Here/below are the specific instructions on the radio programming (pg. 159 of above link).

Good luck & please flag if "HELPFUL". Thanks!

(from section) Luxury Audio System

Selecting the AM or FM frequency band

Push the "AM" or "FM1/FM2" button to select the desired frequency band. Pushing the "FM1/FM2" button more than once will alternate between FM1 and FM2. These functions are used with the station memory buttons described under How to tune radio stations.

HOW to tune radio stations

There are four ways for you to tune in a particular station. You can use the "TUNE", "SEEK", 'SCAN"or memory buttons.

• Using the "TUNE" function: You can change the frequency up or down one increment at a time by Pressing and releasing either the left (< arrow/up) or - right (> arrow/down) side of the "TUNE" or "TUNE DISCS" button. To change frequencies quickly, press and hold down either the right or left side of the button.

Manual tuning adjusts your radio to any allowable broadcast frequency, whether or not a station is present on that frequency. (See All About Radio Frequencies in this section.)

• Using the "SEEK" function: Press the right *) side of the "SEEK" button to select the next listenable station up the frequency band. Press the left (.4) side of the button to select the next listenable station down the frequency band. By holding the button down, listenable stations can be passed over to reach the desired station. Pressing the "SCAN" button will begin the scan mode up the frequency band, stopping on each listenable station for approximately five seconds. To stop the scan mode on the presently sampled station, press the "SCAN" button again.

Setting the station MEMORY PRESET buttons: Your radio is equipped with 6 station memory buttons. These buttons can be used to select up to 6 preset AM stations and 12 FM stations (6 in FMI and 6 in FM2)

1. Select a band, then select a frequency.

2. Press one of the memory buttons and hold until the sound returns and the lamp above the memory button lights up. That
memory button is now set.

3. Follow the above steps for each memory preset button.

NOTE: Custom memory presets can be recalled using the keyless entry system. See Memory Profile System in the Features chapter.

Using the Automatic Memory Store feature ("AUTOSET"): If the memory buttons have been set, either by using the Auto Memory Load feature or if you have set them manually, the system is prepared tolet you use a convenient feature called Automatic Memory Store.

With Auto Memory Store, you can continually set strong stations into your memory buttons without losing your originally set stations. Your radio will automatically set your memory buttons to the strong local stations.

Activate Auto Memory Store by pushing the "AUTOSET" button once. Your radio will set the first six strong stations of the band you are in (AM, FMI or FM2) into the memory buttons. The display will flash "AUTO" and display the autoset icon "A" while the stations are being set in the memory buttons.

NOTE: If there are less than six strong stations in the frequency band, the remaining unfilled buttons will store the last strong station detected on the band. After all stations have been filled, the radio will begin playing the station stored on memory button 1.

To deactivate the Auto Memory Store mode and return to the manually-set memory button stations, simply push the "AUTOSET" button. Display will show "AUTO" then "OFF". The next time Auto Memory Store is activated on that band, the radio will store the next set of six strong stations.

Press on the Menu key and get into Tuner list, look for this function if any.
Seek or Scan --Auto/Manual
PTY must OFF
Seek Sense --- set to high if indication is LO1,2,3 Hi 4,5,6 choose Hi 6

From the main menu, select the icon that looks like a little radio
To search for the next stronger signal, press and hold the up or down arrow
To fine tune the frequency, briefly press the up or down arrow

From the main menu, select to enter
radio mode.
• The earphones cable acts as FM
antenna.
Manually tune a radio station
While in mode, you can manually tune to a
radio station:
1 To search for the next stronger signal,
press and hold / .
2 To fine tune the frequency, briefly press
/ .
Auto-tune preset radio
station
The auto-tune feature of GoGear Vibe helps
you find radio stations and save them under the
preset numbers.
1 While in mode, select [Auto tune] >
[Yes].
»» The radio automatically tunes radio
stations and saves the frequencies to
presets.
»» There are 20 presets available.
»» To stop auto tuning, press .
»» To exit radio, press and hold for 2
seconds.
EN

there is more than 1 channel you can set to on sirius try setting your fm to 108 and set siriuus to same if you go into yor sirius tuner you can use the up and down arrows to tune in the stations

Press the Menu button. At some point it'll put an 'M' next to the station frequency. Then hit the seek up and down button.

While pressing the BAND button, press the DISP button for 2 seconds or MORE to enter the clock editing mode.

To move between the hour and nimute fields, use the left (hour) and right (minute) buttons.

To store the clock setting, press the BAND button.

Also to change between manual tuning and seek tuning press and hold the BAND button for 2 seconds of more. "SRCH" will appear in lower side of display when in search mode.

To preset a station manually press the BAND button to select the band at which to store the station (AM, FM1, FM2, FM3).

Tune to the desired station to be preset

Press and hold the corresponding preset button (1-6) for at least 2 seconds to store the station into memory.

check your setting on the itrip unit to make sure it is set for frequency

I just bought a 3.5 mm aux cord for my ipod but when i press the SRC button, the AUX option does not appear. What am i doing wrong setting this up?

Google the model and download the manual.