I have removed the five screws on the back of the cover. The cover can now be lifted a little bit in the back but wont come free from the front. Are there tabs that have to be released in the front?

Remove book holder at back by pulling it off by hand. Undo the screws visible at the back cover, there's about 4 or 5 or so there. Unclip that centre back panel now screws are out. Remove clear beans cover, remove water tank, lift up the lid to drop grounds direct to brew chamber. Both side lids in open position. Now firmly grip the top cover and try and slide it directly backwards. If it is stuck a firm thump against the front side of the cavity you removed the water tank from while still pulling the top cover backwards will free it up. The sides lift directly upwards to get them off. When replacing the water tank side panel you need the front door open to clear a little spring leg.

UNPLUG UNIT remove three screws in back of dryer holding top, from in front of machine slide top to back of unit to remove, now you will see secrews securing panel to unit also two secrews come from inside unit to the front after these 4 screws lift user innerface panel straight up..
Now after that ck for connectors loose or unpluged hopefully, if not your going to need the tech sheet and a elec . meter to test system

Hello,

Yes your phone can be fixed.

The problem probably could be from the power supply or from the panel.

If it is the power supply, then it most likely could be that it got exposed to a high current and the board got burnt.

To fix this, all you have to do is to replace the panel.

To replace the panel;

1. Remove your back cover, battery, sim and memory card. Two screws need to be removed,
2. Run something like a credit card under the camera surround. It's stuck down with double sided tape so will come away quite easily. You now have access to two more screws. Remove these screws.
3. Run something like a credit card around the join of the front and back cover in order to release the front cover.
4. The front cover will still be attached by a wire. The connector from the wire attaches a bit like a plug and socket and can be levered off with little force.
5. Two more screws, need to be removed.
6. Now lift the main body of the phone away from the back cover.
7. Turn the main body of the phone over and you'll see a ribbon connector. This attaches like a plug and socket. Just lever it up, away from the phone, to unplug.
8. Then you replace the panel of the phone,
   
9. The LCD screen can now be lifted away from the phone.
10. Reverse the whole procedure for reassembly.

take care

Turn off the calculator and turn it over with the back facing you. Using a small Phillips screwdriver, remove the four screws from the back cover. Carefully pry off the back cover. Using a small Phillips screwdriver, remove the screws from the metal battery cover and lift the cover off the battery. Tip the calculator slightly to remove the battery. Caution: Avoid contact with other calculator components. Install the new battery with the positive sign (+) sign down (not showing). Replace the battery cover and the screws that hold it in place. Align the screw holes in the back cover with those in the calculator, then snap the back cover onto the calculator. Replace the screws.

The battery is a CR2032.

first remove the 4 screws at the back. then remove the top cover of your printer. tilt the printer with the front going upward. u will see two screws on the middle of front portion of the printer. remove it along with the screw on the side of it. then slightly lift up the back portion of the cover put a stopper in between so it wont return. turn to the front of the printer then push the top edge gently while lifting the side one at a time. after the clip on the front unlocks, u could safely remove the cover...

...if all 3 lights are on...
This is a laser mirror motor problem.
If you are a little bit technician then...
Remove all cables, open front panel, remove the cartridge, remove the 2 screws on top and 3 on back side, remove a white latch from underside left (or right i don't remember ).
With a small screwdriver release 4 tabs that hold back cower and remove it.
Pull a little bit on under front edges for releasing two little tabs and remove the whole cover by lifting it..
Now you can see the laser scanner unit with a yellow label on it.
Remove the screw, release the tabs an remove laser cover after removing one or two little cables over it.
You can see now a rotating square mirror fixed over a little disc, secured with a little plastic black tab.
DO NOT TOUCH THE MIRROR WITH BARE HANDS or you will make it dirty .
Rotate the black tab to release the disc, remove the mirror with a clean cloth, and put a small drop of synthetic oil on its rod... that's all.
Hope you can do it.

take the top off first by removing the two screws in the back, then the five screws which hold down the door section. the door will lift off and then follow the instructions

put back back on with top off remove screws in top corners of front panel remove bottom panel and screws holding blower/lint screen housing on remove door springs remove screws on bottom corners of front belt is probably lying in bottom

Canon typically hides the screws under the metal plate on the shoe itself. You have to free it at the front and slide it back to get access to the screws holding the shoe

I am not an expert but I do have a Hotpoint 9334 Tumble Dryer which I guess is similar to the 9314.
To replace belt or heater element you must remove the front panel complete with door.
Screws are different sizes in different places so note where they belong as you remove them.

1. Remove 2 screws at rear top which go through the brackets holding the top panel, slide back the top panel a little and lift it off.
2. Pull off the rotary timer knob and remove 2 screws beneath.
3. This is the tricky bit! Remove the the plastic panel which covers the switches etc.. This panel has 5 plastic fingers which secure it to the metal plate behind, locate the ends of the fingers where they pass through the metal plate. Using a metal rod or punch and a hammer, tap the ends of the fingers to push them back through the holes easing each in turn a little at a time to avoid distorting the plastic unduly. (This is a bit scary as you have to hit them quite hard and the fingers look fragile)
4. Open the door and remove the 4 screws then remove 3 screws at the top and 3 screws at the bottom of the front panel. Lift and ease forward the front panel, unhook the door catch release wire, pull off the electrical connectors and put the front panel aside.
5. Lay the machine on its back and remove 1 screw holding the element housing to the top plate and pull off the electrical connectors.
6. Fit the belt around the drum, through the idler pulleys and over the motor spindle.
7. Put it all back together.