I have linksies router and 2 wire modem will they work together?

You dont require a modem as there is a built in modem in linksys router.

Hello
Try this

1 disconnect all wires,including power from the modem and router.
2 Find reset button on router usually in the back,need a pen tip or paper clip to hold it in.
3 Hold in reset for 1 min.
4 Reconnect modem first,power up.
5 Reconnect router second, power up.

Try changing the ethernet wire from the modem to the router.

So your going to have your cable coax wire to the modem.Then a ethernet wire from the modem to the router,then a ethernet wire from the router to the computer.

Sounds like you may have one wire in the wrong place.

The easiest way is to run a long Ethernet cable from one of the 'LAN' (or 'network') ports on the "first" router to the 'WAN' (or 'Internet') port on the second router. The "first" router is the one connected to your cable-modem or DSL-modem. Both routers will auto-configure themselves for this "wired" connection. Configure the wireless-adapter in the second router as per normal.

Or, run a long Ethernet cable from the cable-modem (or DSL-modem) to a location in the "center" of your home, where you can put your wireless-router, such that its signal spans the entire building.

Or, move the cable-modem (or DSL-modem) to a location in the "center" of your home, and connect the one router at that location.

You dont need that CD, in fact I recommend NOT using it.
1. Power off your cable or dsl modem for about 30 minutes 2. Also power of the router 2. Connect a cable from the modem to the Internet port on the Linksys router 3. Connect your PC to the router. 4. Power ONLY the dsl or cable modem on NOT the router. 5. After about 1 minute power on the router.
Should work now.

You will need to assign a different ip address to the Westell modem - I am assuming that both the router & modem are using the same ip address 192.168.1.1? If that is the case, then assign 192.168.1.2 to the modem.

1. Enter your router web configuration by typing "192.168.1.1" on your browser URL
2. Enter your ISP account information
3. Setup your SSID name, secure your wireless with WEP or WPA keys
4. Save settings.

ok once your internet is resolved you shouldnt need to have any computer hard wired to the router but it should go like this cable from your wall to the modem, then cable from modem to the router, after that you can go wireless all the way just make sure that its all secure and encrypted dont want the next door neighbor stealin your internet

you have to power down all three items , turn on the computer then the modem then the route if this fails hit the reset button on the modem this shoul work for ya

if i were to guess you are probably a PPPoE user with a dynamic IP address.

possible config

hello sir iam working for voip and iam a tech?
and u r using linksys pap2 which is not a router its just a phone adapter so it will work through a router so try this first
is ur modem is a modem router and u have 4 ether net port on it and u can able to access inter net through hard wired and connect this pap 2 adapter through one of the ether net jack on the modem router (ut starcom)>an dit has a fire wall which block ur voice signals so u need to open some ports on it try this link to open all ports and u need to try this with a pc which connected through hard wired on the modem router go to through this link
http://www.portforward.com/english/routers/port_forwarding/UTStarcom/UT-300R2U/Vonage.htm

and also disable the fire wall on the router screen and reboot the linksys pap2 and ur ut star com modem router also and connect ur phone directly to phone jack 1 on the pap 2 device if u have any issues let me know
and rate me solved if its helps thx