Will not show screen

i could be that the rechargeable batter is weak. try replaceing the battery for a new one. also check that the connections for the battery are clearn.

I hope this was useful.

Besides the auto-flash mode, you can select fill flash, flash off, self-timer, and nighttime-view with or without flash.
Press the MODE-SELECTOR BUTTON until the desired indicator appears on the LCD PANEL.
Fill flash and flash off modes remain selected after you take the picture. To cancel the selection, press the mode-selection button or close and reopen the lens cover/flash to return to the auto-flash mode.
Fill flash
When bright light indoors or outdoors comes from behind the subject (backlighting), dark shadows (especially on faces) may occur. Use fill flash to lighten these shadows.

1. Open the LENS COVER/FLASH to raise the flash and to turn the camera ON.
2. Press the MODE-SELECTOR BUTTON repeatedly until the FILL-FLASH INDICATOR appears on the LCD PANEL.
3. Frame your subject within the VIEWFINDER EYEPIECE.
4. Partially depress the SHUTTER BUTTON. When the FLASH/CAMERA-READY LAMP turns off and the fill-flash indicator on the LCD panel stops blinking, fully depress the shutter button to take the picture.

Flash off
When you do not want to use the flash, especially indoors where flash is prohibited, such as in theaters and museums, or when you want to take twilight scenes or distant subjects that are beyond the flash range, or capture the ambiance of existing light, use the flash-off feature. Use a tripod or place the camera on another firm support, and use high-speed film because the shutter speed in these situations will most likely be slow.

1. Open the LENS COVER/FLASH to raise the flash and to turn the camera ON.
2. Press the MODE-SELECTOR BUTTON repeatedly until the FLASH-OFF INDICATOR appears on the LCD PANEL.
3. Frame your subject within the VIEWFINDER EYEPIECE.
4. Press the SHUTTER BUTTON to take the picture.

Self-timer with auto flash
Use this feature to include yourself in pictures.

1. Use the TRIPOD SOCKET to attach the camera to a tripod or place it on another firm support.
2. Open the LENS COVER/FLASH to raise the flash and to turn the camera ON.
3. Press the MODE-SELECTOR BUTTON repeatedly until the SELF-TIMER INDICATOR appears on the LCD PANEL.
4. Frame your subject within the VIEWFINDER EYEPIECE.
5. Press the SHUTTER BUTTON. The SELF-TIMER LAMP will glow and then blink during the last three seconds of countdown.
   • To cancel the self-timer selection before the shutter releases, close the flash.
   • The self-timer automatically turns off after the shutter releases.

Night-view with flash
In this mode, the camera balances the flash and existing light exposure so you can take beautiful pictures of people at sunset or at night. Use a tripod or place the camera on another firm support, and use high-speed film because the shutter speed at night will most likely be slow.

1. Open the LENS COVER/FLASH to raise the flash and to turn the camera ON.
2. Press the MODE-SELECTOR BUTTON repeatedly until the NIGHTTIME-VIEW INDICATOR with flash appears on the LCD PANEL.
3. Frame your picture in the VIEWFINDER EYEPIECE.
4. Press and hold the SHUTTER BUTTON for 12 seconds without lifting your finger. Note: If you remove your finger from the shutter button before 12 seconds, the shutter will time out immediately.
   
5. After 12 seconds, release the shutter button to take the picture.

Night-view without flas
In this mode, you can capture the natural existing light of city-night scenes or fireworks at night. Use a tripod or place the camera on another firm support, and use high-speed film because the shutter speed at night will most likely be slow.

1. Open the LENS COVER/FLASH to raise the flash and to turn the camera ON.
2. Press the MODE-SELECTOR BUTTON repeatedly until the NIGHTTIME-VIEW INDICATOR without flash appears on the LCD PANEL.
3. Frame your picture in the VIEWFINDER EYEPIECE.
4. Press and hold the SHUTTER BUTTON for 12 seconds without lifting your finger. Note: If you remove your finger from the shutter button before 12 seconds, the shutter will time out immediately.
   
5. After 12 seconds, release the shutter button to take the picture.

Red light indicates that the camera is out of charged., Try to charged your battery for 3-4 hrs if you encounter flashing red on a fully charged battery you need to call kodak 1 800 235 6325 ext 12

You can charged you camera using 5V AC Adaptor or a USB cable taht attached into the computer

The red hand icon flashing shows that the camera is using a slow shutter speed, and is a warning to be careful to hold the camera steady.

You could put the flash in auto mode and it will fire when the light is low.

to make the green square show up just press the shutter button until half (this is called the half press) when the green square shows up then it means that the camera has focused already, if not repeat the process til green square comes out you can press the shutter button fully to take picture when you see the green square...

A stuck shutter is another common failure mode for digital cameras. The symptoms of a stuck or "sticky" shutter are very similar to CCD image sensor failure. The camera may take black pictures (for shutter stuck closed), or the pictures may be very bright and overexposed, especially when taken outdoors (for shutter stuck open).

To confirm a stuck shutter, put the camera in any mode other than "Auto", and turn the flash OFF (you don't want to blind yourself for the next step). Next look down the lens and take a picture. You should see a tiny flicker in the center of the lens as the shutter opens and closes. If no movement is seen, then you likely have a stuck shutter. If so, please see the following for further info and a simple fix that may help:

http://camerarepair.blogspot.com/2009/05/simple-fix-for-stuck-shutter.html

For your camera (the A460) it's not possible to set the shutter to 15 seconds. Instead, set it to manual mode, turn off the flash, go to a darkened room, take the picture and open the door while the red and yellow light are flashing. Repeat until the shutter becomes unstuck. However, I must say that the chances are probably not very good to fix this with this method. And unfortunately professional repair will be too costly. If repeated tries do not work, it might be time to consider a new camera.

If the shutter is stucked there is no external way to release it Have to show it at camera shop

does the red bulb show when the flash is ready to shoot ? you can press the button that lights red or green to test the flash on itself.

Hi,

Your pictures are blurry because the camera did not focus properly on the subject.

First, turn on the camera in any picture taking mode (or video mode), then look at the screen or viewfinder. There should be four white corners in the center of the camera display. This is your targeting area.
---------------------------------------------------------------------------------------
1. Aim the camera at your subject so this center area is directly on it.

2. Press the shutter button lightly, not all the way down. Wait for a second or two WITHOUT RELEASING YOUR FINGER. If the white corners turn green, keep the finger on the button and press it all the way.

(Once the screen flashes black, a picture is taken and you can release the finger).
----------------------------------------------------------------------------------------
If the targeting area turns red and blinks, then the camera has not focused. You can to try to focus again by following step 1 and 2. If a picture is taken when the targeting area is red, then the picture will be blurry.

If there is no targeting area, then you can still focus by aiming the camera at your subject. Now follow step 2. A green box will appear on the subject, then a sharp picture can be taken.
-----------------------------------------------------------------------------------------
The red arrow that flashes means that the pictures or videos are being written onto the memory card.

Also, try to be steady when taking pictures, because slight hand movement can cause blurry images too.

Page 25 in the DMC-FZ7's english manual will also explain how to focus.

Your camera is set at twilnight mode which has the flash suppressed and you won't be able to turn it on because of the fixed setting of twilnight mode to get the proper result of the picture. Due to the mode setting requirement, a shakey hand icon and no flash icon will show. If you press the flash mode button, it beeps. The twilnight setting has a low shutter speed, i.e. the shutter opens longer to allow more lights in, therefore it shows recording to let you know that the shutter is still open, and any moment of the camera will result in a blurred picture.
Now, check your camera mode dial and turn it back to the 'green' camera and see if you can get the flash to fire.