On the symphonic tv how can I get it to swith the input mode. I am trying to set up WII

You must have its remote control to select inputs.

Check whether signals from Xbox is compactable to TV inputs. Check the inter connection cables.

As there is no "Menu" button to this set at its front panel, you must have its remote control to select inputs.

no possible unless set has actual video or input button on it---almost all the Symphonic sets only have this feature on the original remote.

Usually this is either a cable or a mode issue. First make sure that you have the correct cable connections. (Composite video cable to a component video jack is one possible cause of the problem.) Component video cables are not included with the set but will give better results. However, composite video in from the wii's composite video out should give good results.

If you are using HDMI or component video cables, then go into the Wii video menus to select the correct mode for your tv. Check your TV manual and the Wii setup guide for details on the mode (resolution, etc) you should be using.

If the problem persists, try new video cables and make sure that they are fully seated on both sides. Try switching inputs if you have several available.

I hope this helps.

Cindy Wells

Hi,

The input from the Sega wont be on any channel number - you need to select the correct input for the Sega using the "INPUT SELECT" button on the Symphonic remote control supplied with the TV. Switch on the TV the Sega, then press this button repeatedly until you can see the picture from the Sega.

- If you are using the sockets on the BACK of the TV, the correct input is "VIDEO 1"
- If you are using the sockets on the FRONT of the TV, the correct input is "VIDEO 2". You can also switch to the "VIDEO 2" input by pressing the "GAME" button on the Symphonic remote - if you still have it.

If you don't have the Symphonic remote, look for a button marked "INPUT" or "SOURCE" if you are using a universal remote.

If you don't have any remote for the TV, you will only be able to use the sockets on the front of the TV. You will then need to switch to "GAME MODE" by using the buttons on the front of the TV:

1. Switch ON the TV and the Sega;
2. Press the MENU button;
3. Press the VOLUME UP button to open the PICTURE MENU;
4. Highlight GAME MODE using the CHANNEL UP/DOWN buttons;
5. Set GAME MODE to "ON" using the VOLUME UP/DOWN buttons;
6. Press MENU again to close the menu

You should now be able to see the picture from the Sega. If not, check you have correctly connected the Sega to the TV. When you have finished using the Sega you will need to use the method above to switch game mode off again.

Hopefully, I've covered every possible angle. If you have a different Symphonic TV model from the one listed above (ST420FF), the method should be similar, but if you have any difficulty, please post back for further assistance.

BElectric.

press menu on the tv, press the volume up button, and select on

AV button on tv remote or video remote

the only way to turn i to the input is by pushing the button "input" or "game" on your remote. "input 1" is the back connectors and "input 2" is the front connectors. "GAME" is also the front connectors but it turns that "game mode" on that is in the picture settings. suggest you read the manual that came with the tv too. it explains this all in there with pics and stuff.
if you lost the manual here is a link to it on there website.
http://www.symphonic.us/pdf/om/ST420FF.pdf

hope this helps.

External inputs are accessed in the game mode
set must be in game mode to see video

Press the MENU button so that the menu display appears on the TV screen.
Press the VOL(ume) ▲ button so that "PICTURE" is selected.
Select the feature you wish to adjust with the CH(annel) ▲ or ▼ button and adjust it with the
VOL(ume) ▲ or ▼ button.

GAME MODE
Set to the most suitable position for TV
GAME.
[+] : ON
[-] : OFF

When you press the GAME button if the TV is
off, the TV turns on and will be in the Game
mode and external input mode automatically..