Errof 6C10 on cannon 4600

http://fix-your-printer.blogspot.com/2011/06/how-to-fix-error-6c10-on-canon-printers.html

This article will help you assist with your problem....Happy Holidays,Steve

This error is related to the ink absorber/waste ink tank located internally in the printer. Normally you would have to send your Canon to be serviced to resolve this problem, but there is a video turotial on YouTube that shows how to reset this error: Canon MP550 Ink Absorber Reset (6C10 Error Code) - YouTube

Double check that the error isn't 6C10. I also thought I had an 8C10 error also and that's how I found your unanswered question! But I couldn't find any other internet reference to 8C10 but I did find a YouTube fix for a 6C10 error message. So I got my reading glasses and looked again. Sure enough it was a 6C10 error! I followed the instructions for the 6C10 error fix (resetting Ink Absorber Reset) and my printer is now functioning. Bonus note: My printer is a MP620 and the reset was for a MP550. Same error number though! and also same solution. By now your printer has probably crossed that printer rainbow bridge... but hopefully someone else will need your help? With my reset, I am going to run my $$$ ink cartridges out instead of maintenancing the absorber and then toss mine as well!

Check this method to reset:
6C10 Error

This error could appear on these Canon Pixma printers: MP110, MP540, MP630, MP620, MP640, IP3600...

Solution 1:

• Move the printhead to the center.
• Disconnect the printer and check on the right: is the purge unit ok ? No peace of paper ?

Solution 2:

• Do a reset of the printer:
• Power on
• Hold down the "Resume" button (triangle in a circle) for 15 to 20 seconds.

Solution 3:

• Power off the printer.
• Open the door.
• Power on.
• When the cartridge is in the center, close the door.

Solution 4:

• Open the lid and allow the ink cartridge carrier to center itself.
• Looking to the right, you will see a row of white rollers behind the carrier.
• At the end of the rollers there is a small, clear piece of plastic that sticks up. Take a small piece of a paper towel and wipe all of the ink off this piece of plastic. When that is clean move on to the ink pad.
• About 1 inch, towards the front of the printer from that piece of plastic, is a small square, about 1/2 inch per side, that is a small foam pad. This is where the excess ink is collected.
• Take a piece of paper towel and press into the foam. Do this until the paper towel is no longer collecting ink. Close the lid, turn off the printer then turn it back on.

source: http://fix-your-printer.blogspot.com/2011/06/how-to-fix-error-6c10-on-canon-printers.html

This WEB site gives a solution to your problem.
http://fix-your-printer.blogspot.com.au/2011/06/how-to-fix-error-6c10-on-canon-printers.html

Have you tried this tricks How to fix error 6C10 on Canon Printers ~ Fix your printer ! .Good luck

This appears to be the " absorber full error message".
This message is never due to the operating system, from what I read.
This is a hardware error.
I am afraid I was not able to dig up a direct solution to this answer. The manufacturer (Cannon) requests you have one of their repairmen come to repair it.
This link is to another 6c10 error problem, perhaps it can help you.
http://www.fixya.com/support/t1766019-canon_pixma_mp620_error_6c10_please
I wish I could be of more help to you. :( -Denny

Comment faire pour surmonter les dommages perinter canon ip 6c10 4600? S'il vous plaît guide

Try uninstalling the printer from computer and reinstalling. This should reslove the issue.