Samsung Printer:
My Samsung printer is showing Transfer Belt Error
Hi
I have a utility to reset the consumables errors on this printer, but only if the component is past its lifecount. (60k for transfer belt)
Its called CLP-300_Reset_RLCv04.exe or just RLCV-04.exe (if you can find a copy)
If you need a copy, let me know and I'll find some way to get it to you.
I've used it for transfer belt reset and it works.
Peter - same problem with me here in New Zealand. Can you email the utility? [email protected]
I have this problem- just need to reset it so I can use up toner in stock before I ditch Samsung for good
Hi,
can ihave a copy of this software.
Please my printer don't want to print after i change the trasfer belt.
Send it on my address [email protected]
Thank you
Sorry about not replying, the Fixya site has only just alerted me to these requests for the reset tool.
please add your email address and I'll send the tool to you.
Please send to [email protected] Thanks :)
Sorry, can you send me again?
My address is [email protected]
Thank you i wait for it!
Can you please add me to receive this reset tool please?
I have 2 of these that stopped at 6004.. surprise!!!
[email protected]
Thanks in advance
I have this problem. Please, send utility CLP-300_Reset_RLCv04 on my address [email protected] Thank you.
I have this problem. Please, send utility CLP-300_Reset_RLCv04 on my address [email protected] Thank you.
Not sure if you will still pick this up, but could you email me a copy of the .exe - [email protected] Thanks.
Hi
Please can you send the utility to [email protected]
If you can it would be greatly appreciated.
Kind Regards
Si
Hi
Any chance you can please can you send the utility to [email protected]
If you can it would be greatly appreciated. We have searched high and low and have a CLP-310 which has had a new belt and needs resetting.
Kind Regards
Si
Hi Peter, hope you are still around, will be great if you can sent the utility to [email protected] much appreciated from down under.
Hi Peter, hope you are still around, will be great if you can sent the utility to [email protected] much appreciated from down under.
Peter. Can You email to me the utility? I have two printer with the same error. [email protected]
Thank You very much
Hi can you please send me the utility software I have problem with the transfer belt on my Samsung 300 thanks . my email is [email protected]
hi master..plz send this stuff to me .tanx dude.. [email protected]
Hi Peter, would appreciate a copy please. Have searched but keep finding dead links or russian sites that I don't trust. My email is roweshill#hotmail.com - you know what I mean.
Hello Peter. I don't know if you still pick these up but I would be very grateful for the utility too, if you could send to [email protected] I will be writing to the CEO of Samsung to point out that arbitrarily setting a "stop" on these machines is not green or ethical. Worse thing that can happen is that eventually the printer dies completely, but I would be no worse off than I am because either way I will just buy a new printer, but I object to throwing something away that is working fine save for reaching a particular count. Thank you, Michael.
Hi Peter, I have same problem, too. Could you send the file to me to the mail address [email protected]? I really would appreciate this. Regards Dirk
hello Peter, I have the same problem. Could you send a copy to [email protected] Thanks Tom
hello Peter, I have zhe same problem. Can you send me a copy to [email protected] Thanks James
I would be grateful for a copy as I can't find it online and I have the same problem - Samsung not prepared to do anything about it. Please send to [email protected]
please sir, i am having this same transfer belt error on my printer, i will be greatfull if i could get a copy. [email protected]
I would be grateful for a copy as I can't find it online and I have the same problem - Samsung not prepared to do anything about it. Please send to [email protected]
Hello. Same problem but impossible to find the program. Please, can you send me a copy? [email protected]
Thank you very much.
Hi there, would someone please send me the tool too? I can not find a copy... [email protected]
Thank you!
hola tambi?n necesito la herramienta para resolver mi problema con la cinta de transferencia ... [email protected].... le agradecer?a su ayuda amigo.. gracias..
help CLP-300_Reset_RLCv04.exe or just RLCV-04.exe (if you can find a copy) [email protected]
×
Need to change transfer belt.belt has gone thru its life.
Please send to [email protected] thanks :)
×
SOLVED!!!!! lo solucione, despues de mas de 10 horas de desarmar limpiar sensores decenas de veces,de esta manera:
Mi problema fue "error en la cinta de transferencia" luz roja. En ocasiones, despues de abrir y cerrar la tapa de los cartuchos de toner, el primer "test" que realiza la impresora quedaba con luz verde...OK, pero, no imprimia, volvia la luz roja al intentarlo.
Lo que hice fue, con la impresora con luz verde del primer test, abrir levemente la tapa trasera, la que provoca el arrastre del papel, donde esta el fusor, y mantener esa tapa apenas abierta sosteniendola con la mano, asi, la impresion se realizo, luego, solo cerre la tapa del todo y listo... Supongo algo se ordena, al hacer esto. Suerte!
Same here, any chance of a copy of the utility. i have 2 of these showing the error
Peter I have the same error message.can you send me the reset tool file?
SOURCE: I have a Samsung that say Transfer Belt Error
hi guys.. iam Aqeel from pakistan.
i've just solved that stucking problem today and tellining u guys who are facing such problems over thr.
All you need to do are two steps:
1- detach the paper tray and push it back correctly.
2- open front door and remove toner cartridges, on left inner side u may see a light sensor which detects the toner cartridges.. simply clean this section by a small cotton bud. and left side of toner unit thr is a sensor door, behind that door there is also a light sensor bulb, which needs cleaning by a cotton bud.
thats all
i hope this will help u fixing that problem.
bbyee
SOURCE: I have a SAMSUNG CLP
You need to check the status of the transfer belt. Press and hold the Stop button for 6 seconds; the LED should blink slowly and then quickly. (If a demo page prints, hold the Stop button for longer when you retry the procedure.) The transfer belt should last for approximately 100,000 black and white pages or approximately 25,000 color pages. Compare the information from the configuration page to determine if the ITB (Image Transfer Belt) is near or past its expected life.
If the unit isn't near these limits, try reseating the transfer belt. Open the front cover by pressing the release button at the center of the top of the cover. Then remove all of the toner cartridges (keep them out of direct light by covering them). Just pull outwards on the handles. Then remove the toner box. Next remove the imaging unit by pulling on the handle (again cover this to prevent damage from the light).
Now remove the ITB. It is at the top and back of the printer. To remove it, press down and then pull out. Inpect the unit for any damage. If it is damaged, replace it. Otherwise, reinsert it in the printer by pushing it in and then up. Reinstall the imaging unit, waste toner box and toner cartridges (in the correct spots). Then close the front cover.
Power on the printer and see if the error remains. If it does, turn off the printer. Then reach to the power switch (on the back) and flip that switch to off. Unplug the printer from both the back of the printer and the wall outlet. After a minute, reconnect the power cord to both the printer and the wall outlet. Turn on the power switch and then power on the printer.
If the error persists, then contact Samsung support. This applies if the ITB doesn't have any obvious defects, a replacement unit or the power cycling doesn't fix the problem.
For detailed images, go to http://www.samsung.com/us/computer/printers/CLP-315/XAA and click on Troubleshooting in the For Owners section on the lower left of the web page. See the Errors section and then Transfer Belt Error. If you have a slightly different CLP-315, click on support and find your exact model. Then do the same thing.
I hope this helps.
Cindy Wells
SOURCE: Transfer belt error
Rather than turn printer off, unplug from power source, wait a few minutes and plug back in. It's worked twice for me so far...
SOURCE: Transfer belt error problem
*Check patch sensor *Alternatively your IBT belt needs to be replaced
SOURCE: samsung clx-2160 printer is showing
transfer belt (and other consumables) will reset follow this procedure:
1. go in diagnose mode:
menu - # - 1934 - menu
2. in tech mode -consumables counter - transfer belt -reset
3. after 20 sec. power off and power on
When transfer belt count 60.000 image need to reset.
good lock!
Your printer monitors the life of your transfer belt. When the transfer belt reaches the end of its
life, the printer displays
80 Belt Exhausted. This message indicates it is time for you to
replace the transfer belt. For best print quality, make sure you replace the transfer belt when
the printer displays
80 Belt Life Warning.
Press
Go to clear the message. The Supplies message appears on the second line of the
display to remind you that supplies need attention. You can open the Supplies Menu to see
80 Belt Exhausted
or 80 Belt Life Warning messages.
The printer continues to display the
Supplies message until you replace the transfer belt. To
replace the transfer belt, use the following steps or the instruction sheet supplied with the
transfer belt.
5,296 views
Usually answered in minutes!
Printer says: "replace transfer belt". I replaced the transfer belt but printer continues saying "replace transfer belt"
×