My siemens washer will not pump the water out or spin

check for blocked pump some washers wont fill or spin if the controls get a pump motor over amp signal

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

And the code is!? Gee I hate when that happens! OK look at these:
F1--Water supply/low water fill.
o 1. Check water supply to machine.
o 2. Replace water inlet valve.
• F2--Water level too high.
o 1. Plugged/Bad water pump.
o 2. Faulty water valve.
• F3--Pump problem.
o 1. Check pump trap and clean.
I go with the last one..Common, then the pump is bad then the valve. But You didn't tell Us!

If you need further help, reach me via phone at https://www.6ya.com/expert/steven_b77d19396bfe2249

check for the pump belt broken or off,clogged pump or sock or small item clogging the tub outlet to pump hose. the pump pulley may have become loose on the shaft also

I would take the back off and look for a small 5mm pipe leading upwards from the base of the drum and take it off and blow gently into it you should hear a click and one when you release the air if so then the place where you took the pipe from is blocked clean it out with a pipe cleaner or metal rod and replace the pipe as sometimes this pipe gets blocked with soap goo preventing the water sensor from doing its job eric

same problem

Leaks water...check the pump first. The fill valve and hoses may be the next step. See how to take apart info. With the use of plastic drain hoses on many machines today, this has become a common leak trouble maker. The drain hose can rub the wall or a pipe and this will rub a hole in the drain hose.
 

1. Agitation problems and agitator dog repair aid info
   
2. Automatic dispenser information
   
3. Common problems with Inglis, Whirlpool, Kenmore direct drive style of washers
   
4. Diagnostic Direct Drive washer chart from American appliance
   
5. How a washer works, good to read this first
   
6. Help for storing an appliance
   
7. How does the agitator come off my washer ??
   
8. How to prevent socks from getting into your pump
   
9. Ohm test a common direct drive motor
   
10. How to by-pass a lid switch for testing the washer
    
11. Basic information: Inglis, Whirlpool, Kenmore Direct drive washers
    
12. Inglis, Whirlpool, Kenmore Direct drive washers - How to take apart - Cabinet off, cabinet on, checking or replacing a lid switch, replace the pump, replace motor coupling or motor.
    
13. Inglis, Whirlpool and Kenmore direct drive washer- useful parts breakdowns
    
14. Important disclaimer
    
15. My direct drive washer will fill ok, agitates ok but when it comes to the spin and drain cycle the washer comes to a screeching halt...no spin, no draining and the timer stops, what's up?
    
16. My clothes have a whiting on them that looks like lint.
    
17. My washer has a funky odor
    
18. Noises
    
19. Ohm meter testing a motor capacitor
    
20. Slow water fills
    
21. The wash tubs on my direct drive washer are leaning to the right...why?
    
22. Timer stalls or missing cycles
    
23. Timer will not advance
    
24. Tips on changing a common washer fill valve
    
25. To learn more about washing machines, click here
    
26. Washer Basics: Filling with water
    
27. Washer leaks water
    
28. Washer moves around to much
    
29. Washer will not spin
    
30. Washer sample wiring diagrams
    
31. Washer spins and agitates at the same time
    
32. Washer belts: If your belt on any washer looks like these, replace the belt(s).
    
33. Washer runs but wont agitate or spin
    
34. Washer won't run, agitate or spin
    
35. What is that black power powder or filings under my washer??
    
    
    

it will fill but won,t spin, will throw out water as if it washed, then it take water to rinse but won,t spin ,then will throw out water as if it did , but clothes are soaked

go back to water vavle and start form there ,,is it humming..verifie water in fill hoses,,check and make sure you have hoses on dispencer correctly,,if removed,,,check and make sure you did not twist or kink hose entering tub...make sure connection are on the water valve..onthejob

check the pump ,,, if pump wont pump out the washer wont spin till it gets down so low / larryyb

Perhaps the exit hose behind your machine is not at the correct height, about 3 feet from ground. Your pump pumps the waste over this height, into your standpipe or sink; check this out.