Printer wont power up

How Reset Canon PIXMA error 5200: The printer is turned off and plugged the power cord. Press the button STOP / RESET and hold, then press and hold the POWER button. POWER button is pressed, release the STOP / RESET, then press the STOP / RESET 2 times in a state of the power button is pressed. Release both buttons simultaneously. Press the power button, then the printer will off Press the power button again, then the printer will be lit and ready for use.

If this does not solve the problem, here is another method:
I have found a solution for your problem. (1) With the printer turned on, unplug it (2)Open the top and bring the ink cartridge holder to the middle (3)Raise the gray bar and remove the print head assembly with the cartridges in it (4) Lower the gray bar with the head missing and close the top with the head out (5) Restore the power,wait til the printer wakes up (6) It will tell you to put in the cartridges (7) Restore the print head, close the top and the printer should resume working.

I have found a solution for your problem. (1) With the printer turned on, unplug it (2)Open the top and bring the ink cartridge holder to the middle (3)Raise the gray bar and remove the print head assembly with the cartridges in it (4) Lower the gray bar with the head missing and close the top with the head out (5) Restore the power,wait til the printer wakes up (6) It will tell you to put in the cartridges (7) Restore the print head, close the top and the printer should resume working..... ;)
bhupi

Hi,

Please try below, it could help you tio fix the issue.

Solution 1: Power Drain

1. Make sure printer is OFF.
2. Disconnect the printer power cable/ Camera and PC usb cable.
3. Disconnect the power cable from wall outlet.
   
4. Press and hold the power button for 30 seconds.
5. Connect the printer power cable and turn ON.

Solution 2: Printer Reset

1. Take the ink cartridges out.
   
2. Disconnect all the cables connected to printer.
3. Press and hold "OK" and "CANCEL" button at same time.
4. While holding the button connect the power cable and continue holding the buttons
5. The printer displays "NVM reset" , then release the buttons. (Printer might turn itself down, don't worry just power ON it back.)
6. Insert the cartridges when you see printer displaying "Missing Ink catridges".

Regards
Riztech
If this solution is helpful,kindly vote 'thumbs up' and write testimonial feedback.

here is some reset procedure for canon i80 printer

1. Turn off the printer.
2. Press and hold down the Resume/Cancel button
3. Press and hold down the Power button.
4. While holding down Power button, release the Resume/Cancel button.
5. While still holding the Power button, press 3 times the Resume/Cancel button.
6. Release the Power button
(printer will initialize, LED blinks in green)
7. When the Led steadily lights in green, press the Resume/Cancel button 4 times.
8. Press the Power button and wait until the printer initialize again and return to menu selection.
9. Turn off the printer and then turn on again and print a test page.

I hope that is what you needed.
Please comeback and do rate this solution.
Thanks for using Fixya.

reset unit unplug it for 1 minute try that

In this scenario you should check with a new set of black cart or you can try by cleaning the cart with a lint free cloth. and try with resetting the printer as well. if it doesnt work then printer might have gone bad

this signal cartridge miss mach please reinstall your cartridge power of & power on again then 1 is active printer is ok or change your printer cartridge Black and color both

Something is jammed somewhere, turning the power off is not the reason that the jam indicator won't go out...you're missing something. Check all areas of the copier -just because the "Z" is lit doesn't mean that the remaining jam isn't somewhere else

No, there is no reset button.
disconnect the pirnter from the computer and the power cord. press and hold the power button for 30sec. connect the power cord, and connect it back to the computer.

If a brother printer wont turn on its usally a problem of the main pcb! Due to power or lighting strikes the microdevices might be shortcuted. Its cheaper to buy a new printer than to replace the board!