Missing channels I have done channels scan auto programming on the TV and it still won pick up certain channels like 2 the TV guide

The auto scan picks up whatever channels are available, if it only picked 2 then that is all you have available

A channel scan is a vital part of utilizing your cable TV service. When a coaxial cable is connected to a TV, sometimes it will not display any channels until you configure the TV for your specific cable connection and scan for available channels. A channel scan can be applied to basically any type of TV or TV/VCR combo, even if you are missing its remote control.

Read more : http://www.ehow.com/how_6875646_do-old-tv_vcr-tv-remote_.html
Instructions

1. • 1 Bring up the TV's menu. Look for a button on the front panel of your TV/VCR labeled "menu" or "setup." Press it and you should see a menu appear on the screen. Part of the menu should inform you what buttons you can use to navigate through the menu. If not, try using the volume buttons or channel buttons on the front of the TV and see if pressing those allows you to navigate through the menu.
     
   • 2 Specify channel scan settings. Once you are able to navigate through the TV's menu, look for the "channel scan" "auto-program," or "auto-tune" option. This may be inside one of the TV's sub-menus such as "setup," "channel setup," or the like. The key of this step is to specify your cable settings before running your channel scan. The "tuner mode" option needs to be set to "cable" rather than "air" or "antenna." You may have to specify what cable type to use, this will be set to "std" or "standard" for the vast majority of cable providers. If you are not certain what cable type you use at home, contact the technical support department of your cable provider.
     
   • 3 Run a channel scan. Once the scan settings have been set properly, run the scan (usually done by pressing a "start," "scan" or "begin" button.) When the scan is complete, check to see if you are getting all of your channels. Contact your cable provider if you are not sure how many channels you are supposed to be getting.
     

Read more : http://www.ehow.com/how_6875646_do-old-tv_vcr-tv-remote_.html

good luck

on B:Press the MENU button on the remote.Select Setup.Select Auto Program.Choose Air or Cable.Select Auto Program to let the TV reprogram the channels.Check that the channel is programmed into memory. There are a couple of ways to do this: Use the TV menu system. Accessing this setting varies depending on the model TV that you own. Here are two options that are common on many TV's: Option A:Press the MENU button on the remote.Use the VOL and CH buttons to move through the menu and add any missing channels try this if not r
Do a full reset if this dosnt work

The auto scan feature scans the various channel frequencies looking for a signal. Weak signals may be picked up on one scan and missed on the next. Check your antenna or add a antenna power booster and try again.

Mine did that and I had to tighten the connection better from the wall cable into the input.

check weather some of your channel was deleted in the program. just add those channel so you can make auto scan programs.

Used the tv remote go into tv Menu goto SETUP go down Ch. enter pick CABLE and enter again.Tv now will go into auto scanning for CABLE channels.After the auto scan done for the CABLE channels are finish.After this u will able to go to channel 60 to used the dish remote.

Hello
Here is the procedure for auto tuning. Pleas go through it. Connect the antenna to the rear antena socket marked as &% ohms antena and continue.

If you have already run the Auto Tuner as part of the quick setup earlier in this guide, please

skip ahead to "Channel Summary" to continue setting up your television. In Auto Tuner Setup,

the TV automatically scans through all available channels, memorizing the active ones and

skipping over blank ones or channels with weak signals. This means you scan using the

CHANNEL +/- buttons), you will receive only clear active channels.

Press the MENU button

?† To AUTO TUNER SETUP

?® To operate

?® To choose CABLE or AIR

Press the OK button to start

Initial Setup

Auto Tuner Setup

Programming will take approximately 1 to 2 minutes. The auto tuner is finished when the

message PROGRAMMING OVER! appears onscreen.

Channel Summary

Channel summary allows you to customize the line-up of channels received by your TV. You

can add or delete channels from the line-up or prevent any unauthorized viewers from watching

any or all 181 channels.

Press the MENU button

?† To CHANNEL SUMMARY

?® To operate

The Channel summary screen will now be displayed with

the channels set to scan marked with an "?". You can delete

channels from the scan by removing the "?". If any channels

were missed during auto tuner setup and you wish to add

them, you may by placing an "?" next to the channel number.

?† ?® To the SCAN column

Press the OK button to include or delete from scan

Press the MENU button when finished

You can block access to a channel by activating the channel lock.

Press the MENU button

?† To CHANNEL SUMMARY

?® To operate

?† ?® To the Lock Column ( )

Press the ZERO button to lock or unlock that channel

Press the MENU button when finished

Press the MENU button when finished

AUTO TUNER SETUP
CABLE
If you wants any codes, contact me through Fixya. Ok
.
I'm quating these procedure from the manual I've with me, and it is for JVC AV32S565.

run auto scan......please make sure you dont run power scan.....once scan is done you should get all the missing channels back.