Printhead for office hero 6.1 - Kodak Office Hero 6.1 All-in-One WiFi Printer Print, Copy, Scan, Fax

https://www.worldclassink.com/Brother-MFC-240C-Printhead-printer14311-ift18.html
Free shipping on allBrotherMFC-240C Printhead. Genuine. Free $25 gift certificate for all orders over $100. Next day and second day shipping available. Free Shipping OnBrother

1. This error occurs due to an abnormal increase in temperature of the RH printhead.
2. Follow the forthcoming guidelines to fix the issue. Power off the device.
3. Insert the power cord to the appropriate ends and turn the printer on.
4. If the problem persists, replace the print head.
You can purchase a new printhead from the manufacturer's store. 5. If the issue continues, update the firmware of your Canon printer.
6. Check the image quality and reinsert the printhead of the printer.

Please follow the below link to the Kodak website for this code:
Printhead carriage jam or all in one printer error code 3515 3525 3527...

Kodak HERO 6 1 Extended User Manual http://resources.kodak.com/support/shtml/en/manuals/urg01259/urg01259c11s1.shtml

Error: "Printhead Failure" (105-3802) - Kodak

support.en.kodak.com/.../error%3A-printhead-failure-(105-3802)

KodakAug 25, 2010 - How do I resolve the error message "Printhead Failure" (error code ...If you are not prompted to calibrate the printhead, turn off the printer, wait ...

Error: "Printhead is missing, not installed correctly, or has ...

support.en.kodak.com/.../error%3A-printhead-is-missing,-not-inst...

KodakAug 25, 2010 - How do I resolve the error message "Printhead is missing, not installed correctly, or has come loose" (error code 105-3513) on my ESP or HERO All-in-OnePrinter? ... If the printhead and ink cartridges are not installed in the printer, install them: ... If the error continues, restart the printer and try to print.

If the ink cartridges and printhead are already in the printer, remove them, then reinstall them.

1. Remove the color and black ink cartridges.
2. Remove the existing printhead by lifting the latch in the center of the carriage. ESP 3, 5, 7, 9, 3250, 5250, 5210,
   ESP Office 6150, 7250, 9250;
   HERO 7.1, 9.1, OFFICE HERO 6.1 ESP 1.2, 3.2, 3.2s, C110, C310, C315,
   ESP Office 2150, 2170;
   HERO 3.1, 5.1
3. Close the printer access door.

Check the LCD on your printer control panel or the status monitor on your computer for an error message. If there is an error message, follow the instructions to clear it.

If there is no error message, or if the problem continues:

1. Open the access door.
2. Disconnect the power adapter from the back of the printer.
3. CAUTION: Do not use force on the printhead carriage to move it. Gently move the printhead carriage from side to side to see that it moves freely and there are no obstructions.
4. Remove any obstructions that may prevent the printhead carriage and ink cartridges from moving to the center position.
5. Close the access door.
6. Connect the power adapter to the printer.
7. Remove the ink cartridges from the printhead.
8. Verify that the labels on the ink cartridges are intact, and that the cartridges are not damaged.
9. firmly until you hear it click into position.
   
10. Insert the color ink cartridge into the printhead, then press down firmly until you hear it click into position.
    
11. Close the printer access door.
12. Press OK to clear the error.
13. Make a print.

You may have dried ink in the printhead. You can remove the printhead and try cleaning it at home in hot soapy water, rinse, then leaving it to dry thoroughly. Certainly won't leave you any worse off than you are now, and may well do the trick.

If you have not already performed serveral head cleans I would strongly recommend doing more. A problem of this nature almost always comes back to the printhead being blocked, dried or defective. It may be worth replacing one or more of the cartridges just in case you had recieved a defective one (but this is very unlikely).

In all honesty the printheads in this range of printers were a little unreliable. There was a period when we had people reporting Kodak sending replacements with very little resistance to resolve all manner of print quality issues. As such it may be that there is a genuine issue with the printhead itself that cannot be resolved.

The decimal selector works for only 0,1,3,4, and 6. 2 does not work and unfortunately that is the only one I need to use, (who cares about 5). Can this be fixed?
Sharp Compet QS-2760A