Reason code=1
I have a point to multi-point solution with the multi-point in WDS-AP mode and the clients in WDS mode. All 3 clients were up (for several years) until today.
One client failed this morning, and I replaced it. Two others were up, but after I put in the replacement, the other two went down with reason code=1. The replacement is up.
Security settings did not change on the multi or the two clients.
I have had similar problems with DWL-2100 and (much less often) with DWL-3200. I have no solution, but a workaround: changing the authentication mode. For example, if the units are using WPA-Personal, I change it (on both) to WPA2-Personal or WPA-Auto-Personal. It doesn't seem to matter which mode is used, it's just the fact of changing it that helps (eventually). You may have to go through the process more than once. Also, realize that although the web interface comes up 30 seconds or so after a reboot, it may take another 30-60 seconds before a link is established, so don't give up too soon while trying these changes.
Dear Sir,
I have to worked on the DLINK DWL-2100AP AS POINT TO POINT with WDS with AP AND second one WDS Without AP
(1) First Install the Router ADSL &Wimax (and check the internet)
(2) Second you are install the DWL 2100AP WITH Mode WDS with AP and connect with the another WDS take the Mac Address in the WDS With AP and WDS With AP take the MAC Address in the WDS AND it connect the router with the Lan cable With the WDS With AP
(3) Third you are configure the WDS on the second DWL-2100AP
(4) You remember that both WDS With AP and WDS Same SSID like DLINK and other one same SSID like DLINK
(5) Be Care full you are use the Same WAP \WEP like that same and Same PASSWORD
(6) When you are enter the net work in the wireless then you see only one DLINK
(7) I try this one it s fine the working
(8) If any trouble then send the mail I help you Thanks [email protected]
I have d-link wireless access point,DWL-2100Ap, i need to setup my wireless connection,for 10 computers , what i can do?
15,106 views
Usually answered in minutes!
THU SEP 11 20:31:35 2008
System
--AP cold start with f/w version: v2.20e
u
THU SEP 11 20:31:35 2008
Wireless
--WLAN1 Normal AP ready
THU SEP 11 20:31:40 2008
Wireless
--Received Deauth: WLAN 1 11A STA 00:15:
00:4c:24:46 reason code=1
THU SEP 11 20:31:54 2008
Last message repeated 7 times
THU SEP 11 20:31:54 2008
Wireless
--Received Deauth: WLAN 1 11A STA 00:15:
00:4c:24:46 reason code=1
THU SEP 11 20:32:01 2008
Last message repeated 7 times
THU SEP 11 20:32:01 2008
Notice
--Ethernet AE1 LINK DOWN
THU SEP 11 20:32:11 2008
Wireless
--Association:11G STA 00:15:00:4c:24:46
associated with WLAN1 SSID = 3rd Flr
THU SEP 11 20:33:11 2008
Notice
--Ethernet AE1 LINK UP
THU SEP 11 20:33:21 2008
System
--Web login success from 192.168.0.51
THU SEP 11 20:34:11 2008
Wireless
--Received Disassoc: WLAN 1 11G STA 00:1
5:00:4c:24:46
THU SEP 11 20:34:24 2008
Wireless
--Deauth: WLAN1 11G STA 00:15:00:4c:24:4
6 reason code=1
THU SEP 11 20:34:24 2008
Wireless
--Received Deauth: WLAN 1 11G STA 00:15:
00:4c:24:46 reason code=1
THU SEP 11 20:35:35 2008
Last message repeated 7 times
THU SEP 11 20:35:35 2008
Wireless
--Received Deauth: WLAN 1 11G STA 00:15:
00:4c:24:46 reason code=1
Feb 1 14:42:16
Wireless system with Mac address 00:22:b0:c6:bc:5b deauthenticate reason 6
Feb 1 14:42:16
Wireless system with Mac address 00:22:b0:c6:bc:5b deauthenticate reason 8
Hi. Same problem here. Been working mostly very well for a couple of years, but the last several weeks, constant disassociation. I've tried everything, including realigning external antennas, cleaning all the antenna connectors, changing various settings on both units etc. etc. No solution yet. Maybe they only last a couple of years, and then wear out ?
×