My maytag bravo top loader washer is displaying a code of LF and

OL = Overloaded.

Is the Washer overloaded? If OL (overloaded) appears in display, the load too large. If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent.Feb 24, 2020

OL - Error Code - Top Load Washer - Product Help - Maytag

Maytag https://producthelp.maytag.com > ... > OL

The washer has ol on it at the end - Maytag Bravos quiet ...

iFixit https://www.ifixit.com > Answers > View > The+washe...
Oct 6, 2014 · 2 answers
First, OL stands for "Overload", so in other words, the washer thinks the tub is too hard to move because it's overloaded and the motor is ...
OL code all the time even with very small and light ...
2 answers
Sep 28, 2016
Why washer stops and gives code "ol" - iFixit
2 answers
Nov 30, 2016
at the end it says OL - Maytag Bravos quiet series 300 ...
1 answer
Dec 29, 2022
OL code showing . - Kenmore 110 Series Washing ...
2 answers
Sep 19, 2017
More results from www.ifixit.com

I have a Maytag Bravos washer and it had got progressively worse with LF code often having to restart several times. Checked every thing then bought a new inlet valve assembly from McComb supply. Replaced it and it works good. Note: wires were soldered on tabs.

Water valve stopped up. Check screens in the valve and hoses if present in hoses.

Maytag Bravos MTW6600T Top Load Washer Run ... - Fixya

www.fixya.com > ... > Maytag Bravos MTW6600T Top Load Washer

Maytag Bravos MTW6600T Top Load Washer, run diagnostic test cycle related issues. Get free help, solutions & advice from top Maytag experts.

Maytag Bravos MTW6600T Top Load Washer Run ... - Fixya

www.fixya.com > ... > Maytag Bravos MTW6600T Top Load Washer

Maytag Bravos MTW6600T Top Load Washer, run diagnostic test ccu related issues. Get free help, solutions & advice from top Maytag experts.

Maytag Bravos MTW6600T Top Load Washer Diagnostic ...

clean the lint filter

LF (F30)
LF flashes when the control don't sense any water coming in like it is supposed to do. Things to check:
Hoses connected; water turned wide open.
Hose screens plugged.
Is water siphoning out due to having the drain hose too low? (30 inches above the floor)
Pressure hose from tub to control loose, pinched, hole, Sediment in tub? Blow that tubing out and re-secure; retry with water OUT of tub so the pressure can properly build in that tubing.

Bravos codes and service manual HERE

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Defective hall sensor most likely, The cabrio bravos and Oasis machines are all basically the same.
MORE here

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

That means low flow. Turn up water valve. If that don't work then shut your water off take off hoses and clean the screens on the washer they are dirty that happens with hardwater

(Washer is taking too long to fill)
Check the following:
Are the hot and cold faucets turned on?
Are the water inlet hoses kinked or clogged?
Are the water inlet valve screens clear?
Press POWER/CANCEL to clear display.

Hope this helps.........................

Have same problem. Service tech said LF code is caused by low water pressure coming into machine. Tech verified water flow looked fine, getting new controller installed tomorrow.