Technofit TS500i treadmill error code?? ( E1 & E2) please help!!!!!!!!!

Question edited for clarity and its proper name.

E1 is a speed sensor error. Sometimes it just needs cleaning/

E1 Error Codes

The Treadmill Engineer http://www.treadmill-engineer.com > 2016/02 > e1-err...
Feb 29, 2016 - If the E1 error occurs after the belt starts to move for several seconds, the error code means that the system is not picking up the speed of ...

Missing: 5090 ‎' Show results with: 5090

jkexer e1 Questions & Answers (with Pictures)

Fixya https://www.fixya.com > Forum > Tags > jkexer e1
...jkexer polar 5090 treadmill and its coming up E1 any ideas please 1) You must adjut the speed sensor, clean it, tight the connector very well.see the ...
images

..

Hi,

from what I'm seeing for the dishwasher, an E1 error means that the door is not properly closed. So, please look at the door of the machine to make sure that nothing is broken or that the dishwasher isn't too full. Thank you.

HI There,

We would need to know the make and model of the treadmill as they are vastly different electronics wise. The error E1 can indicate a mismatched speed error, no belt movement when it is expected, or a faulty lower control board may also cause this. Older Matrix Fitness machines used "E" for elevation errors and "S" for speed errors but most have changed that format to E1, E2, etc..
Good Luck!

Replacement Parts for Fitness Exercise Equipment at SPORTSMITH

True Treadmill Errors and Service Messages

• The True 600, 700, 725 and 750 series treadmills are equipped with built-in diagnostics and maintenance reminders that display either an error message or service message as they occur.
• The error messages that may be displayed by the built-in diagnostics are as follows:
  • E1:INCLINE
  • This means that the incline is moving when it has not been commanded to.
  • E1:MINIMUM
    • This is a minimum incline calibrating error that can be cleared by calibrating the incline.
  • E1:RANGE
    • This means the difference between the treadmills zero position and maximum incline is not sufficient.
  • E1:STALL
    • This means that the incline is not moving when it has been commanded to.
  • E2:OVERSPEED
    • This occurs when acceleration greater than 2.1 mph occurs as this is greater acceleration than anticipated.
  • E2:CAL
    • This means feedback cannot reduce or increase speed to target and error can be cleared by calibrating treadmill.
  • E3:EEPROM
    • This error happens when a data error is detected on the EEprom. The control panel needs replaced if this error occurs.
  • E5:SENSOR
    • This error occurs when there is no speed or RPM feedback detected from speed sensor.
• The service messages that may be displayed by the built-in maintenance reminders are as follows:
  • S1:LUBE
  • This service message displays when it is time for inspection of the deck lubrication system.
  • S2:CLEAN
    • This service message displays every 500 miles and is your prompt to clean the treadmill.
  • S3:MOTOR
    • This service message displays every 2500 hours and is your prompt to check the motor brushes.
• This information should help you understand the cause of the error message or code and how to take action to repair your True treadmill

Errors for True Treadmills E5 Sensor E2 Cal S1 Lube and more

If someone spilled a drink on the belt, it will become sticky as it dries. The belt will try to stick to the bed of the treadmill. Loosen belt, wipe clean the bed, underside of belt, and end rollers.

adjust and clean the speed sensor, and tight the connector very well, see the diagram
2) test the input voltage motor, if there are voltage the motor replace
3) test the output voltage board, if there are NOT voltage , the board is faulty, replace.
God bless you

see this steps and fix it.God bless you
This is probably a 1( faulty speed sensor, adjust it , clean it and tigh the plug very well see the diagram attached. 2( test the input voltage motor, if there are the motor need repair 3( test the output voltage board, for input voltage motor, if there are NOT the board is faulty see the block diagram . The error codes will differ between makes and models but could be e1. or e2
Run the software calibration for easy diagnostic, troubleshooting, and fix it.
God bless you

I have a technofit ts500i with a broken computer but the motor and treadmill still work. would you consider selling your computer consol only

Trimline treadmill starts up then code E2 comes up, and the display shuts down. 
Any ideas???