BELKIN ROUTER, NO CONNECTION WITH WEBSERVER INSIDE

Solution:

Step 1:
Make sure the that router is connected to your modem with an ethernet cable via the router’s internet (WAN) port.

Step 2:
Unplug the modem from its power source and make sure that it's totally turned OFF. Then re-plug the modem to the power source.

Step 3:
Unplug your router’s power supply, wait for 10 seconds and then plug it back in. This will cause the router to reestablish communication with the modem.

If you still cannot browse the web, contact your Internet Service Provider (ISP).

Solution:

Step 1:
Make sure the that router is connected to your modem with an ethernet cable via the router’s internet (WAN) port.

Step 2:
Unplug the modem from its power source and make sure that it's totally turned OFF. Then re-plug the modem to the power source.

Step 3:
Unplug your router’s power supply, wait for 10 seconds and then plug it back in. This will cause the router to reestablish communication with the modem.

If you still cannot browse the web, contact your Internet Service Provider (ISP).

Solution:

Step 1:
Make sure the that router is connected to your modem with an ethernet cable via the router’s internet (WAN) port.

Step 2:
Unplug the modem from its power source and make sure that it's totally turned OFF. Then re-plug the modem to the power source.

Step 3:
Unplug your router’s power supply, wait for 10 seconds and then plug it back in. This will cause the router to reestablish communication with the modem.

If you still cannot browse the web, contact your Internet Service Provider (ISP).

Site reference link:
https://www.belkin.com/us/support-article?articleNum=56519

press red reset button in back for 2 minutes.

Hello,
The router is designed in such a that it is compatible with all the computers. The best way to get rid of this issue is log into the router interface and change the wireless channel to suit your requirement.
1) To begin with.. Open internet explorer on a computer connected to the router and delete everything from the address bar and type http://192.168.2.1 and hit enter. Now you will be in the Belkin Router setup. It will ask for a login password when you click on anything.. Leave the password field blank and click on submit. 2) Towards the left side under wireless click on "Channel and SSID". Now you see wireless channel change it to different channel and click on "OK / Save". Now check the signal strength in your Acer computer. If its still the same try different channel and check.
Hope this helped.

Hello Kgmas,

You can setup the router simply by connecting to the router webpage. The default address should be 192.168.2.1; just connect to your router with an ethernet cable and then type the IP address into a web browser to access the page.

Once in the router web page you can set the administrative settings (password for the router) and you can set up your wireless network manually fairly easily.

Thanks,

Pat

Hello
Sounds like you took all the right steps.In add and remove programs at the control panel,remove your wireless card drivers and anything related to it.
Be sure to write down your wep security key from your router first.

Then remove the card,reboot,put the card back in,then reinstall the drivers.

If this does not work the wireless card may be bad.

Hope this helps.

1. all u need to do is download the firmware for ur router
2. most of the belkin products if u update the firmware it will work great
3. go to belkin.com/support and download the firmware. jus click on this site it will lead u to download ur version

http://en-us-support.belkin.com/app/answers/detail/a_id/301/p/386

4. u need to save it in the desktop screen
5. open the belkin router setup page by 192.168.2.1 in the ie or firefox
6. in the left side click on firmware update then leave the password blank and click submit
7. then click on the browse choose the file which u downloaded from the site
8. click on the update and after the reboot of the router ur good to go.

In order to download software for your device you will need to know the wireless technology (G), the model no. (F5D7230-4) and the version (?). Look at the underside of your router and you should see the model number and the version which is something like v7000, v8000, v9000, etc. Then go to the Belkin.com support page at http://en-us-support.belkin.com/app/product/list/q/routers/session/L3NpZC9vV2tsSS1Nag%3D%3D and follow the prompts. After you enter the required information, you will be taken to a page were you can download software, drivers, and firmware for your device. You can also peruse the FAQs and download manuals and documentation, etc.

dcurtp

You would have to log into the router to configure port forwarding on port 80. You would have to know the IP address of the computer hosting the website and put that in the routers config under port forwarding.

Try to look for MTU settings on the router's admin page. Since your on DSL connection, set the MTU size to 1492 and save the changes. You need to power cycle the router after that. Good Luck!

If you're connected to the router with excellent stregth then the problem most likly lies in the routers connection to the internet. Check your DSL, Cable modem and make sure the connection to the "Internet" port on your router is good. Try switching out the Ethernet cable if nessciary.