Nortel Norstar T7316 programming extention to button. Won't let me program extension 230.

HERES A MANUAL THAT MAY HELP https://www.broadconnect.ca/resource-centre/user-guides/nortel-phones/M7310-User.pdf

PDF]Telephone Features Programming Guide - Avaya Support

https://downloads.avaya.com/css/P8/documents/100142941 AvayaNORTEL NETWORKS is a trademark of Nortel Networks. ... All other trademarks and registered trademarks are the property of their ... One-line and two-line displays . ...Memory buttons . ... Call anomalies for telephones without line buttons . .... Select how you dial your calls . ... Receive a busy signal on an internal call .

Norstar How to program phone how to program voice mail ...

www.phonserv.com/1_PDF_user_guide_meridian_norstar_phone_syste...

Nortel Networks Meridian Norstar How to program voice mail phone feature codes ...Modular ICS KSU must be programmed with an M7310 or a M7324 telephone. ... Lift handset, press Voice Call key or press the Feature button, then press 66 2. .... At the LOG: prompt, enter your mailbox#(extension #. and your password all ...

[PDF]N QRTEL NORSTAR

You should be able to enter programming from any T7316 or M7310 or M7324 phone. Does this happen at the other phones which can be used for programming. If it does, try a power reset of your phone system.

Did you mean "Line" in use?

Caller calling Voice Mail probably tied it up.

Tech needs to program Supervision Disconnect for the line/s and Carrier must do the same so they talk to each other.
So when callers hangs up a disconnect signal tells the system to hang up.
90 percent of the time the tech had it programmed but the carrier did not.

Programming is done on M7310, M7324 and T7316 sets.
To set up ringing you need to enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt,
press the show key (top right arrow).
The display should now ask for an extension number. Enter extension number you wish to program ringing on.
Press the show key (top right arrow)
The display should sat LINE ACCESS
Press the show key (top right arrow) .
The display should say LINE ASSIGNMENT.
Press the show key (top right arrow) .
The display ask for a line number. press list
The display should say line 001: appear & ring
press the Chng key till it says appear only
press next key (lower right arrow)
The display should say line 002: appear & ring
repeat the procedure the same as line 001 for the remaining ringing lines

press the release key when finished

You can program a memory button with a new number or
feature.


External autodial:

1. Press (Feature), ( * ), (#1).
2. Press a memory button.
3. Dial the external number.
4. Press OK to store the number.
5. Label your new button.


Internal autodial:

1. Press (Feature), ( * ), (#2).
2. Press a memory button.
3. Dial the extension number.
4. Press OK to store the number.


How to erase memory buttons:

1. Press (Feature), ( * ), (#1).
2. Press a memory button.
3. Press OK to erase the button.

Alternatively, you can download the Nortel T7316 Quick Reference Card from IdacomUSA, your solution for Nortel Repair and Refurbishing.

If the extension was a swap of the old M7310 with a new(ish) M7310 no additional programming should be necessary. However if the phone was replaced with another type of nortel set(M7208, M7324,T7313 etc.) then the phone will default to its base features. To re-program the feature keys press feature *3, the button you wish to program, and the feature code for that button

You can set divert for the calls to another number. Do check for the call settings and activate the divert based on situation like.. When busy. Not reachable.

Press "Feature **ADMIN", go to NAMES, Then go to Sets, and from their its just like texting

feature 983 it will ask for log number use code 120000 for 2 number extensions, for 3 letter extensions it is 1020000, and 4 is 10020000 once in this screen hit MBOX then CHNG and put in mail box number then hit next until you get to the name and press CHNG and you can change it using the the number corresponding to the letter I hope this helps