How to access door to ink cartridges

http://images10.newegg.com/User-Manual/User_Manual_28-415-214.pdf
Open ink access door.
1. Make sure the printer is turned on. Never turn off the printer when ink cartridges are missing.
2. Open the ink cartridge access door. [This is the panel that is to the left of the touchscreen. To open, put your fingers on the upper left hand side of the panel (by the logo: HP OfficeJet 6700 Premium), You should be able to gently pull the panel so that it opens out.]
NOTE: Wait until the print carriage stops moving before proceeding.
3. Press the front of the ink cartridge to release it, and then remove it from the slot.
4. Remove the new ink cartridge from its packaging.
5. Using the color-coded letters for help, slide the ink cartridge into the empty slot until it is securely installed in the slot.
Replace the

Open cartridge access door, observe left side door switch located, manually operate it feel weather its working or not, close door & check.. not rectified, insert peace of paper in it. check...

To resolve the issue:

1. Make sure you install the correct type of KODAK Ink Cartridge for your printer. Currently we offer two types of ink cartridges (10 Series and 30 Series). Installing the wrong type of ink cartridge may result in this error. You will need to install a new, correct type of KODAK Ink Cartridge.
   NOTE: For more information, see Which ink cartridges to buy for all-in-one printer.
2. If you are using the correct type of KODAK Ink Cartridge, reinstall the color ink cartridge.
   1. Open the printer access door.
      NOTE: If the ink cartridges don't move to the center, see Printhead and ink cartridges don't move to center with access door open.
   2. Wait until the printhead is idle and silent, then pinch the latch on the color ink cartridge with your thumb and forefinger and lift it out of the printhead.
   3. Install the color ink cartridge back into the printer, making sure to press down on the thumb tab until it clicks into place.
   4. Close the printer access door. For printers with LCDs, follow the instructions on the LCD screen.
      For more information on installing ink cartridges, see the Extended User Guide for your printer. Review Maintaining Your Printer - Replacing ink cartridges.
3. If the error continues, restart your printer:
   1. Turn off the printer by pressing the power button.
   2. Wait five seconds.
   3. Turn on the printer.
4. If the error continues, and you have extra, new KODAK Ink Cartridges on-hand, try to install a new ink cartridge (or a set of new ink cartridges).
5. If the error continues, contact us.

When the issue is resolved, we highly recommend that you upgrade the firmware for your printer for optimum performance:

1. Locate and select the firmware for your printer.
2. Follow the instructions to install the firmware.

Source: http://support.en.kodak.co.uk/app/answers/detail/a_id/39315/selected/true

Hi,

Here are some steps that can help you resolve the problem.

Close the cartridge access door securely, if cartridge access door is open even slightly, the print cartridge light will blink.
1. Open the cartridge access door, once carriage moves to the center of the printer.
2. Check inside the printer and make sure that there are no obstructions that are preventing the cartridge access door from closing , if there's any obstruction remove it.
3. Close the cartridge access door completely.
Do the Print Self Test
Press and hold the Cancel button, and then press the Start Copy Color button
Release both buttons at the same time
If the issue persists, Make sure that the cartridges are installed
1. Open the cartridge access door, once carriage moves to the center of the printer.
2. Wait until the carriage is idle and silent
3. Check the cartridge slots in the carriage to make sure that the cartridges are installed.
4. Try to reinstall it again.
5. Lightly press down on a cartridge to release it, and then pull the cartridge toward you out of its slot.
6. Check the nozzles on the cartridges to see if the protective tape is still attached
Note: Do not touch the copper-colored contacts or ink nozzles
7. Hold the cartridge by its sides
8. Slide the cartridge into its designated slot at a slightly upward angle.
9. Press the cartridge inward until it snaps into place
10.Close the cartridge access door
Do the Print Self Test
Press and hold the Cancel button, and then press the Start Copy Color button
Release both buttons at the same time
If still the problem persist contact HP for the service.


I hope this will be able to help you.

Thank you for choosing Fixya

The ink cartridges are only accessible when the printer is on. Open the access door on the right front of the unit. (flip the door down by pulling from the side of the printer). If this is a new unit or one that has been packed for transport, remove and save the green protective part. Unpack your new cartridges and turn the green knob on the yellow protective cap clockwise until you here a click. Then pull the cap straight out away from the cartridge. Use the arrow to line up the cartridge with the appropriate slot and push the cartridge into the printer. Push the cartridge forward until it clicks. (Repeat for the rest of the cartridges.) Then close the access door.

If you are replacing cartridges. Open the access door and push down to unlock and release the cartridge you need to replace. The other directions are the same.

If the cartridge carrier doesn't come to the ink access position, close the access door and make sure the printer is on. Check for an error code on the unit. (Clear any paper jams or foreign objects that are blocking the cartridge carrier from moving properly. See the URL below for troubleshooting details.)

You can get the manuals from Brother: http://www.brother-usa.com/mfc/modeldetail.aspx?PRODUCTID=mfc295cn .

I hope this helps.

Cindy Wells

Hello there:
This problem is usually due to a print head that needs to be replaced
I have provided the information that you will need ok
best regards mike
This document provides information on how to replace a printhead or ink cartridge.A printhead may need replacing when print quality issues cannot be resolved by cleaning the printheads or a front-panel display message indicates a printhead needs to be replaced.An ink cartridge needs replacing when a front-panel display message indicates either:

• Low ink levels
• Ink cartridge approaching expiration date

CAUTION: Never remove an ink cartridge and a printhead at the same time. Use the table below to identify the correct ink cartridge part number: Ink cartridge Part number HP 14 black print cartridge C5011A HP 14 tri-color print cartridge C5010A Use the table below to identify the correct printhead part number: Printhead Part number HP 14 black printhead C4920A HP 14 cyan printhead C4921A HP 14 magenta printhead C4922A HP 14 yellow printhead C4923A Replacing the ink cartridges Follow the instructions below to replace the ink cartridges:

1. Turn on the unit, and open the print-carriage access door by lifting the handle until the door locks into place. Figure 1: Opening the access door
2. The print carriage will move to the center of the unit.After the print carriage stops, remove the ink cartridge by pressing the gray release button, then lifting the cartridge up and out of its slot. Figure 2: Removing the ink cartridge
3. Remove the new ink cartridge from its packaging and, being careful to touch only the black plastic, remove the tape. Figure 3: Removing the tape
4. With the ink cartridge label face-up, push the new ink cartridge firmly down into the appropriate slot until it clicks into place.The color ink cartridge inserts into the right-hand slot as indicated by the rainbow colored oval. Figure 4: Inserting the new cartridge
5. Close the print carriage access door. CAUTION: If the ink cartridge is removed before a replacement is available, close the print carriage access door and replace the ink cartridge within 24 hours.

Identifying parts of the printheads Use the table below to identify the parts:

1. Printhead handle
2. Printhead tower
3. Copper contacts
4. Plastic tape
5. Ink nozzles

Do not touch:

• Copper contacts
• Ink nozzles
• Printhead tower

Try the following:

1. Open the printer access door.
2. Put out both ink cartridges and the printhead.
3. Let the printer access door open.
4. Put out all paper.
5. Pull out the ac adapter at the back of the printer.
6. Wait 60 sec.
7. Pull in AC adapter.
8. Wait 30 sec. then turn on the printer
9: Wait for the error message: Printer access door open.
10. Close the printer access door.
11. Wait for the error message: Printhead is missing.
12. Open the access door and put in only the printhead and the close the access door.
13. Wait for the error message: both ink cartridges are missing.
14. Open access door, put in only the black ink cartridge, then close the acess door.
15. Wait for the error message: Color ink cartridge is missing.
16. Open access door, put in the color ink cartridge and then close the access door.

If the error is solved, do a firmwareupdate right now.

You can find it here.

Manually slide cartridge to middle of access door, then lift front part of cartridge up and then lift up straight to remove rest of cartridge

How do I resolve the error message "Calibration Page Not Found"? Error code: 3610 Question : How do I resolve the error message "Calibration Page Not Found"?
Answer : To resolve this error condition, correctly position a calibration page on the scanner. See the User's Guide for more information. How do I resolve the error message "Cover open"? error code : 3501 Question : How do I resolve the error message "Cover open"? Answer : To resolve this error condition, close the access door. The printer will not operate while the door is open. How do I resolve the error message "Color ink cartridge missing or not installed correctly"? Error Codes : 3511 Question :
How do I resolve the error message "Color ink cartridge missing or not installed correctly"?
Answer :
To resolve this error condition, reinstall the ink cartridge:

1. Remove the color ink cartridge:
   1. Open the printer access door by lifting from the front center of the unit.
   2. Wait until the printhead is idle and silent, then pinch the latch on the color ink cartridge with your thumb and forefinger and lift it out of the printhead.
2. Check the two electrical contacts on the ink cartridge for small marks, which should appear if the cartridge was installed correctly.
   
   If the electrical contacts do not have small marks:
   1. Reinstall the ink cartridge, making sure you press down on it until it clicks into position.
   2. Remove the color ink cartridge, then check the two electrical contacts on the ink cartridge again for small marks. Repeat if necessary.
   3. Reinstall the ink cartridge.
      
3. Close the printer access door.

NOTE: See the User's Guide for more information about removing and installing the ink cartridge.
If the error persists:

1. In the KODAK All-in-One Home Center, select the Help (?) icon.
2. Select Maintenance.
3. Select Firmware Upgrade, then follow the prompts to download the latest version of firmware, free of charge.

From Kodak support:
http://www.kodak.com/eknec/PageQuerier.jhtml?pq-path=9104/7269&pq-locale=en_US

Click on this link or copy and paste the complete link into your browser.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Well, here is the proper way of fixing or troubleshooting that paper jam error in your printer

Open the printer access door and remove both of the ink cartridge, then remove also the printhead, after that close the printer access door, without those parts. Then it will show a message in the printer screen, "Printhead is missing or has come loose" or "Printhead Not Detected" Install the printhead, just the printhead without the ink cartridges. After that close the printer access door. Then it will show you a message"Ink cartridges is not installed,install ink cartridges". then open again the printer access door, then install the black ink cartridge without the color ink cartridge. then close the printer access door, then message must be " Color ink cartridge is not installed, install color ink cartridge" then install the color ink cartridge." the message must be,"New printhead is detected calibration require, load paper and press start"

Thats the way of overiding the paper jam error message of your kodak all in one printer
hope this will help you guys

by: E.brown

Happy Printing(", )
Kodak AIO tech support 1-800-421-6699