You wrote, There is one sockec that lightbulbs keep blowing in.... Correct?
What type of light are we talking about? If it is a regular run of the mill porcelain lampholder there is not much to go wrong with the light itself. If on the other hand it is a Compact Flourenscent (CFL) there are a few components to it that can go wrong.
CAREFULLY visually inspect the inside of the socket if it is not a CFL and make sure there is no foreign material in it. Please write back with the type of light it is. You wrote, There is one sockec that lightbulbs keep blowing in.... Correct?
What type of light are we talking about? If it is a regular run of the mill porcelain lampholder there is not much to go wrong with the light itself. If on the other hand it is a Compact Flourenscent (CFL) there are a few components to it that can go wrong.
CAREFULLY visually inspect the inside of the socket if it is not a CFL and make sure there is no foreign material in it. Please write back with the type of light it is.
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Likely there's a wire loose that's shorting to the chassis. The way I troubleshoot these is to put a lightbulb in the fuse socket, and then go under the dash, and move stuff around while somebody watches the light. When it goes on, you're close to the problem. Yeah, it's a royal pain, but that's the best way I know.
Either lose bulb but most likely a charging problem. Get DMM Nd test voltage at battery while the bike is running. Anymore than 14.3 volts you probably have a faulty voltage regulator.
Turn off the fan before you climbing the ladder to remove the dead bulbs
Note whether a screw secures the shade or if the lightbulb holds the shade in place.Unscrew the lightbulb counterclockwise. If the bulb is securing the
shade, grasp the shade with one hand while removing the bulb.Install the new lightbulb by turning clockwise into the socket. If the
bulb holds the shade in place, keep the shade in position with one had
while screwing in the bulb with the other.
Check the tab in the center of he bulb socket. Unplug the frig first and gently pull it up a little. You should be using a 40 watt appliance bulb not a 60. If the tab is not the problem you may need a new switch. Eric
1:Unplug the microwave oven from the outlet. Wait 20 minutes for the capacitor that is inside the microwave to discharge.
2:Unscrew all the screws around the casing by turning them counterclockwise.
3:Remove the cover by lifting off.
4:Locate the light bulb in the microwave. This will be located on either the right or left side.
5:Unscrew the light bulb by unscrewing counterclockwise. Some light bulbs are held into the socket by two notches; for these you will need to gently push on the bulb and turn counterclockwise to unsecure the bulb, then pull out of the socket.
6: Place your new bulb in the empty socket and secure by turning clockwise until tight, or if the bulb is one with notches on both sides, then guide the notches into the slot on the socket, push gently and turn clockwise until clicked into position.
7: Replace the cover and screw back on. You are now done and may plug back in the microwave.
Warning : Unplug the microwave before starting and wait 20 minutes for any residual electricity to be bled off from the capacitor.
Unfortunately, many possibilities. If you have time, start by removing both reverse lamp sockets from light assembly(and keep from touching any metal), remove bulbs from sockets, CAREFULLY INSPECT sockets and wires. New fuse of correct rating. Turn key on and try again in reverse. Fuse still blows: Next place to look is transmission reverse electrical switch and wiring as far as you can trace looking for burned/stripped wires near transmission and wires by sockets Fuse doesn't blow: Turn key off and install one lamp in socket at a time. DO NOT install sockets into fixture at this time. Test. Remove first lamp to check second. If still O.K., each socket back into fixture(one at a time same as before)and test. Most common problems: Sockets contaminated, wires shorting at sockets, bulbs installed incorrectly shorting to ground.
If there is no power to the sockets, changing the bulb wont correct the problem. Check all fuses. Check for current to the tailight. Check for ground to the tailight. Repair as nesessary. Check cigarette lighter filament. It may be faulty. Check inside cigarette lighter socket. It may have a foreign material in it causing the short.
You wrote, There is one sockec that lightbulbs keep blowing in.... Correct?
What type of light are we talking about? If it is a regular run of the mill porcelain lampholder there is not much to go wrong with the light itself. If on the other hand it is a Compact Flourenscent (CFL) there are a few components to it that can go wrong.
CAREFULLY visually inspect the inside of the socket if it is not a CFL and make sure there is no foreign material in it. Please write back with the type of light it is.
×