Set my clock time and temperature - Honeywell RC182WR Atomic Alarm Clock - Red

Atomic clock keeps losing outside temperature Google Search ..try this link not sure if it will help you with yours.

Hi

If you have lost the outside temperature on the clock display then do the following:-

1. Make sure you have good batteries installed in the remote transmitter
2. Remove the batteries from the main clock and keep them out until the clock display disappears.
3. Re-install the batteries in the clock.
4. Wait until the display returns and includes the outside temperature display as well.
5. Set the clock again for current time/date etc.

Also check the link bellow:-

http://www.ehow.com/how_4597931_set-atomic-clock.html

Please get back to us if you have further query else please accept the suggestion.

Thank you for contacting fixya.com

Push the clock button,then push the up or down temperature arrows to set the clock. After it is set,push the clock button again.

SkyScan 86715:
>Press "SET" once,
>>press "+" until you see your time zone;
-4 ATL-Atlantic
-5 EST-Eastern
-6 CST-Central
-7 MST-Mountain
-8 PST-Pacific
-9 ALA-Alaska
-10
-11
-12
-6MT-?
>Press "SET" once,
DST ON/Off
>Press "SET" once,
US - duh, huh
F - MER-Mercredi, French
E - MIE-Miércoles, Spanish
>Press "SET" once,
>>press "+", for correct hour
>Press "SET" once,
>>press "+", for correct minute
>Press "SET" once,
Range 00-20; 09 = 2009
>Press "SET" once,
Month
>Press "SET" once,
Day
>Press "SET" once,
Day of the Week
>Press "SET" once,
12 or 24 hour
>Press "SET" once,
Fahrenheit or Celsius
>Press "SET" once again - DONE!!!
.
The clock should now display "month/day/day of the week/moon phase/Temperature"
.
NOTE: Moon phase and Seconds will correct on first reception from Coordinated Universal Time (UTC)
.
Lastly,
Press "+" once,
Temperature changes to seconds
>>Press "+" once,
Temperature returns on right-most panel and
seconds replaces day of the week.
>>Press "+" one last time and you are back to done!!!
.
Thanks,
.
[email protected]

Batteries must come out of both the temperature sensor (transmitter) and base (clock and temperature display). Leave out for about 4 minutes. Replace the batteries in the temperature sensor FIRST and set it about 5 - 10 feet away from the base. Replace the batteries in the base and leave them both set without touching any buttons for at least 15 minutes (usually only takes 5 minutes or so). The temperature should start to display. You can set the clock manually to the correct time and have it get the updates via radio in the evening or night. Should work after all this just fine. (have done it alot of times this way over the years)

Good luck.

1. Hold down WAVE/SET for about 2 seconds to enter the setting mode.

2. The time zone and DST (Daylight Savings Time) blink. Press + to select your time zone. Press - to turn DST On or Off. The default setings are PST and DST On.

3. Press WAVE/SET again to confirm the setting and enter the year setting mode.

4. The year digits blink. Press + or - to select the year.

5. Press WAVE/SET to confirm the year setting and enter date setting mode.

6. The date digits blink, press + or - to select the time.

7. Press WAVE/SET to confirm the date and enter time setting mode.

8. The time digits blink, press + or - to select the time.

9. Press WAVE/SET to confirm time setting and enter the clock and temperature setting.

10. The time format and temperature blink. Press + to select between 12Hr and 24Hr format. Press - to select between Celsius and Fahrenheit.

11. Press WAVE/SET to confirm whole setting.

SIGNAL: To aquire the signal for the first time, place the clock near a window facing Fort Collins, CO. If it fails, it will try again every 3 hours.

I hope this helps. I work for radioshack and i had a few extra minutes while at work.

Brett.

Please check the following website for all the info and faq.

http://skyscan.info/content/index.php?option=com_content&task=view&id=35&Itemid=40

Also,

If you have lost the outside temperature on the clock display after replacing the transmitter battery then do the following:

1. Make sure you have good batteries installed in the remote transmitter
2. Remove the batteries from the main clock and keep them out until the clock display disappers.
3. Re-install the batteries in the clock.
4. Wait until the display returns and includes the outside temperature display as well.
5. Set the clock again for current time/date etc.
6. Bingo. You are in business.

Please check the following website for all the info and faq.

http://skyscan.info/content/index.php?option=com_content&task=view&id=35&Itemid=40

Also,

If you have lost the outside temperature on the clock display after replacing the transmitter battery then do the following:

1. Make sure you have good batteries installed in the remote transmitter
2. Remove the batteries from the main clock and keep them out until the clock display disappers.
3. Re-install the batteries in the clock.
4. Wait until the display returns and includes the outside temperature display as well.
5. Set the clock again for current time/date etc.
6. Bingo. You are in business.

FixerUpper

Here is how you adjust the time zone:
1.) push MODE till "AL" appears after the minute.
2.) tap "SET" (tap means push but do not hold) and time zone will advance.

3.) THE TRICK: The Time Zone can only be set in the Alarm Mode. Make sure you so not push and hold "SET" until the hour flashes as you would to set the alarm time. You just go into Alarm Mode and tap "SET" to advance the Time Zone by one zone per tap. When the Time Zone is where you want it, tap MODE to return to the clock and set the correct time.

Each time you press the set button on the back it selects one of the items that you can set. For example if the "month" is selected by pressing the "set" button then press the "+" key to change it from 1->2->3->4 etc. Each time you press "+" key the month will go up by one. Stop when you reach the correct month. You can do the same for each item including the time zone and daylight savings time and whether you want your temperature to be in Celcius or Farenheit. Hope this helps...

FixerUpper