In camera mode, screen shows a blend of image and digital spectrum analyzer bars blurring the image

First, rotate the mode selector dial to "Auto", then check to ensure that you're not in macro mode. Also make sure that your lens is clean and there are no smudge marks.

If you've done all the above, and you're still getting blurred images, this then might be a defective CCD imager. If so, Canon should fix this for you for free, including free shipping both ways. This is regardless of your camera's warranty status. Please check this link for more info.

Applicable cameras include:
A40, A60, A70, A75, A80, A85, A95, A300, A310, S1 IS, S60, S200, S230, S330, S400, S410, S500, SD100, SD110, IXUS V2/300/400/430/500, IXY Digital 30/30a/200a/300a/D320/400/ 450/500

Hi,

Apparently the vendor-supplied CCD image sensor used in this Canon digital camera may cause the following malfunction: When the product is used in recording or playback mode, the LCD screen and/or electronic viewfinder may exhibit either a distorted image or no image at all.

To determine if the CCD (image sensor) is working properly, follow these steps:

1. Insert a memory card with known good images on it into the camera.

2. Power the camera on to the Playback mode.

3. Press the DISPLAY (DISP) button to enable the LCD panel, and observe
the LCD.

a. If the images are displayed properly, please proceed to step
four.

b. If the images are not displayed, or a "NO IMAGES" message
appears, please ensure that the memory card contains known good images.

c. If the card contains known good images, and the issue persists
with a second memory card, the camera will require service.

4. Switch the camera to the Camera mode. You may use any shooting mode
(i.e. Auto, Manual).

5. Press the DISPLAY (DISP) button to enable the LCD panel.

6. Point the camera at a well-lit scene and observe the LCD and/or
viewfinder. If the scene the camera is pointed at appears on the LCD
and/or viewfinder, the CCD is operating properly. If the LCD and/or
viewfinder remain black, the camera requires service.

Effective immediately, and regardless of warranty status, Canon will
repair, free of charge, products exhibiting the above-mentioned
malfunction if the malfunction is caused by the CCD image sensor. Canon will also cover the cost of shipping and handling in connection with this repair.



Regards.

did you ever find a solution to this problem ?

OK IF YOUR PRERECORDER VIDEO'S PLAYBACK CORRECTLY THIS IS THE CCD AND CANON WILL FIX FOR FREE. THANKS TO SONY

This sounds like it might be a defective CCD imager. If so, Canon should fix this for you for free, including free shipping both ways. This is regardless of your camera's warranty status. Please check the following two links for more info:

http://camerarepair.blogspot.com/2007/11/canon-digital-cameras-showing-black.html

http://www.usa.canon.com/consumer/controller?act=PgComSmModDisplayAct&fcategoryid=225&modelid=13390&keycode=2112&id=29819

Applicable cameras include:
A40, A60, A70, A75, A80, A85, A95, A300, A310, S1 IS, S60, S200, S230, S330, S400, S410, S500, SD100, SD110, IXUS V2/300/400/430/500, IXY Digital 200a/300a/400/450/500

ssue: The LCD/Electronic Viewfinder will not display an image or the image is distorted.

1. Press display (DISP.) button to turn the display on 2. If all troubleshooting has failed, please have your PowerShot A520 serviced

This sounds like it might be a defective CCD imager. If so, Canon should fix this for you for free, including free shipping both ways. This is regardless of your camera's warranty status. Please check the following two links for more info:

http://camerarepair.blogspot.com/2007/11/canon-digital-cameras-showing-black.html

http://www.usa.canon.com/consumer/controller?act=PgComSmModDisplayAct&fcategoryid=225&modelid=13390&keycode=2112&id=29819

Applicable cameras include:
A40, A60, A70, A75, A80, A85, A95, A300, A310, S1 IS, S60, S200, S230, S330, S400, S410, S500, SD100, SD110, IXUS V2/300/400/430/500, IXY Digital 200a/300a/400/450/500

Failing CCD- if less than a year old return to vendor. If more than a year old contact Canon This may be eligible for free replacement- due to a faulty batch of chips that were in circulation used my many makers,

That is normal. Didital SLRs are different in this respect from digital compacts .

If you turn on the back LCD, the electronic viewfinder will remain on while in a shooting mode. There is no setting on the camera to use only the back LCD monitor while shooting. If you playback images in the Play mode, only the LCD monitor will turn on. However, if you press the Monitor button while in the Play mode, than the back LCD monitor will turn off. The image will display only in the viewfinder LCD.