Reset camera I need to reset the camera so that the date and time are not set????? Please help

Press the MENU/OK button. Press cursor-left, then select the wrench-SET icon. Press cursor-right, then select the DATE/TIME command.

If you need a manual, you may download a copy here.

Sounds to me that there may be another battery inside the camera that is going bad.


Issue: Everytime I power on the camera the Date / Time needs to be set.
Solution: Replacing the Date Battery for the PowerShot A480.

Replacing the Date Battery. If the Date/Time menu appears when the camera power is turned on, the date battery charge is low and the date and time settings have been lost. Please purchase a lithium coin battery (CR1220) and replace it as follows.
Please note that the first date battery may appear to expire relatively quickly after you purchase the camera. This is because it is installed in the camera at the point of manufacture, not when you make the purchase. Be particularly careful to keep the date batteries out of the reach of children. Seek medical assistance immediately if a child swallows a battery since corrosive battery fluids can damage the stomach or intestinal walls. 1. Confirm that the camera power is turned off.
2. Open up the battery door / cover and remove the AA Batteries.
3. Remove the date/time battery holder.
4. Grasp the battery and slide it in the direction of the arrow.
5. Insert a new battery with the (+) side facing up.
6. Replace the battery holder and battery cover.
7. When the Date/Time menu appears set the date and time.
After purchasing the camera and turning on the power for the first time, although the Date/Time menu will appear, you do not need to replace the date battery. If you ever dispose of your camera, first remove the date battery for recycling according to the recycling system of your area.

Hi,
Please follow the steps below to reset the setting to default...

1. Turn on the camera and press the <MENU> button to open the menu. 2. Using the button, highlight the yellow (Set up) tab. 3. Using the button, select [Reset All..] and press . 4. Select [OK] and press .

• Settings cannot be reset when the camera is connected to a computer or to a printer.
• The following cannot be reset:
• • Shooting mode
  • The [Date/Time], [Language] and [Video System] options in the (Set up) menu
  • White balance data recorded with the custom white balance function
  • Colors specified in the [Color Accent] or [Color Swap] modes of My Colors
  • Newly added My Camera settings

Hi,

yes its possible. Please remove the internal battery once and then put it inside after few minutes. This will reset the date time. while you switch it on once again. it will prompt you to enter new date and time.

Regards
Sweet Rascal

Please go into the menu, camera settings, date and time.

You can also reset the camera: Take the batteries out for longer than 10 sec. reinsert and the camera automatically asks you to set date and time.

I understand that you wish to change the date on your KODAK camera.;
Please go into the menu, camera settings, date and time.

You can also reset the camera: Take the batteries out for longer than 10 sec. reinsert and the camera automatically asks you to set date and time.

Please go into the menu, camera settings, date and time.

You can also reset the camera: Take the batteries out for longer than 10 sec. reinsert and the camera automatically asks you to set date and time.

Here is the only information I could find for you. This is a link to the extended user manual. You want to look in two different places. The 1st place to look is "setting up your camera". From there there is a heading for setting up the date and time and language. The 2nd place would be "Doing more with your camera"

http://www.kodak.com/global/en/service/publications/urg00846toc.jhtml?pq-path=12649/12701

Hope this helps.

Can not format disc in T700

Try resetting your camera. In picture taking mode press menu. Go to setup, go up to reset, press right arrow, make sure reset is highlighted and press set.

Then TAKE OUT MEMORY CARD. Go back into menu, go to setup, go up to format, press right arrow and highlight format, press set. Input ur date and time again and then power off and back on. If that doesn't help then you have to send into repairs. 800-706-2534 and keep choosing option 2 and they will tell you where to send it.