Panasonic project pt lb75 how to reset lamb runtime

To reset the lamp hours, turn on the projector. Then press Menu and use the Up/Down arrows to highlight Options. Press Enter then highlight Lamp Runtime. Press and hold Enter for 3+ seconds until the Lamp Runtime screen is displays. Press the Power button (any other button cancels the reset). When the Power button LED turns red, unplug the power cord to the projector. You can either use the remote or the controls on the projector. Reconnect the power cord after a few minutes.

The reset instructions are on page 62 of the user manual. The manual is available from Panasonic here: https://support.panasonic.co.nz/docstore/PT-LB50U%20Operating%20Instructions.pdf .

I hope this helps.

Cindy Wells

1. Press the Power button so that a picture is projected onto the screen
2. Press the Menu button to display the "Main Menu", and then press the F or G button to select "Option"
3. Press the Enter button to display the "Option" menu, and then press the 5 or 6 button to select "Lamp Runtime"
4. Press and hold the Enter button for approximately 3 seconds
5. The "Lamp Runtime" will change to "Time Reset [Power Off]"
6. Turn off the power and disconnect the power cord

Get A Quote for a Panasonic Projector Lamp or to Replace your Existing Projector Lamp now.

Here are some links that will help you.

Change the Panasonic PT AR100U projector lamp in 3 easy steps DLP Lamp...

How to reset the lamp time in Panasonic projector model vex 500

How to Reset Panasonic Projector Lamp Timer Projector Lamp Services

Turn on the projector MENU- OPTION- LAMP RUNTIME- Press and hold the ENTER button for 3 seconds. Turn off the power.

The lamp hours might have not been properly reset.

1. Press the "POWER" button so that the projector projects the picture on the wall (projection screen)
2. Press the "MENU" button to show the "MAIN MENU"
Use buttons "F" or "G" and select "OPTION"
3. Confirm this by pressing "ENTER" so that "OPTION" is shown
Using buttons "5 / 6", select "LAMP RUNTIME" (lamp operation counter)
4. Select and press the "ENTER" button for at least 3 seconds
5. The "LAMP RUNTIME" (lamp operation counter) will change to "TIME RESET[POWER OFF]"
6. Turn the device off by pressing "POWER" and unplug the power cord.

hi,
Do the following for reset the lamp hour timer of Panasonic PT-LM1U
1. Power ON the projector. (wait for the display)
2.Press the menu button to display main menu and then press the up arrow or down arrow to select OPTION2.
3. Press the Enter button t display the OPTION 2 menu.And press the up/down arrow to select LAMP RUNTIME.
4. Press and hold Enter button for approximately 3 minutes.
5. The LAMP RUNTIME will change to TIME RESET. (power off).
6. Turn off the power.
OK

Read very carefully this is the only solution to reset lamp timer

1. Connect the mains lead to the projector and a mains socket, and switch the MAIN POWER on. 2. Press the POWER button.
3. Press the MENU button to display the menu.
4. Select the OPTION menu and press the ENTER button.
5. Select LAMP RUNTIME.
6. Press and hold the ENTER button for approximately 3 seconds.
7. The confirmation screen will be displayed and select OK.
8. Press the POWER button to turn off for resetting the duration of the LAMP RUNTIME.
9. Next time when you POWER ON the projector the duration of time in LAMP RUNTIME is reset to "0 H".

1. Press the MENU button to display the menu.
2. Select the OPTION menu and press the ENTER button.
3. Select LAMP RUNTIME.
4. Press and hold the ENTER button for approximately 3 seconds.
5. The confirmation screen will be displayed and select OK.
6. Press the POWER button to turn off projector for resetting the duration of the LAMP RUNTIME.
7. Confirm the duration of time in LAMP RUNTIME is reset to “0 H”.

1.Press the MENU button to display the menu screen, and
then press the F or G button to select the OPTION menu.
2. Press the ENTER button, and then press the F or G button
to select LAMP RUNTIME.
3. Press and hold the ENTER button for approximately
3 seconds. The confirmation screen, “LAMP RUNTIME
RESET.” is displayed and select OK.
4. Turn off the power.
�� This will reset the cumulative usage time for the lamp
unit to zero.
***Here you go and best of luck!***

Hi,the part # you will need is tyla-1000 ,this are instructions to replace it http://guides.fixyourdlp.com/panasonic/TY-LA1000.php?Click=48173 Have a blessed one.

Pull the left front panel off of the unit and you will find the lamp door behind that panel. It is very simple to pull the lamp and most times you can even see the element in the lamp has blown. You can easily buy and install the lamp yourself.