Getting fault code f14?

Diagnostic mode for Kenmore Elite He3t model 110 42926 ...

iFixit https://www.ifixit.com > Answers > View > Diagnostic...
Apr 8, 2016 - With the washer empty, close the door. · Push "control/on" or "Start" · Select "Drain/Spin" · Select "No Spin" by pressing SPIN SPEED touchpad.
3 answers · 2 votes: I believe this is very similar to the model I have. Here is what I did to run a diagnostic. ...
F11 error code during Diagnostic test? - Kenmore ...
1 answer
Jan 18, 2016
SOLVED: F11 code error on Kenmore HE3 - iFixit
16 answers
Mar 3, 2011
SOLVED: f h error code - Kenmore Elite HE3 ...
9 answers
Feb 21, 2012
It seems like the washer has no power - Kenmore Elite ...
6 answers
Nov 2, 2017
More results from www.ifixit.com

Diagnostic Test; Starting The Test Mode; Test Program ...

ManualsLib https://www.manualslib.com > ... > User manual
Close the door. Select the DRAIN/SPIN cycle. Select NO SPIN by pressing the SPIN SELECT button five (5) times. Push Prewash Option button four (4)times within ...

..

hi check your motor brushes

F14 for Kenmore (Whirlpool) machines means EEPROM Error.

The Central Control Unit (CCU) receives it's data from an EEPROM on board the CCU, if there is an error reading this data, it will cause this error.

A power glitch may cause this error. Try unplugging the Unit for two minutes to see if that fixes the error. Check CCU. So its likely you'll need a new CCU board.

Check your owners manual, some models have up to a 5 year parts warranty on that CCU.

I have a Kenmore Elite he4t front load washer that was working fine and then we moved and now it stops washing midstream and flashes an F and a H. I have to pause and restart then it will stop washing again after a few minutes and flash the same codes again. I reset again and then it stops with 1 minute left and will not drain.

"F02" is a Long Drain error. This is an indication that there's an obstruction somewhere in the drainage system. Most commonly, the drain pump reservoir needs to be checked and cleaned. The access screws are on the bottom front edge of the lower toe panel directly below the door. You may need to prop up the two front feet of the washer to access them (a 2x4 works well for this). The following link explains:

http://www.fixya.com/support/r3574284-checking_the_drain_pump_on_a_front_loade

It does not take much to damage the pump impeller or motor. Since the error code is generated if the drain cycle exceeds 8 minutes, if the pump is damaged and can't pump at the required volume, the error code will continue to appear until the pump is replaced. If the pump requires replacement, the following link explains how:

http://www.fixya.com/support/r3574350-replacing_the_drain_pump_in_a_front_load

Replacements can be purchased online at any of the following websites:

searspartsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com

Prices vary between these sites, so shop and compare.

If you have any questions about this repair, or need additional assistance, please let me know. I hope this helps you.

go 2 repair clinic on line, same codes for whirlpool duet repair help then error code tab

The motor controller board is likely bad.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

HE 4 front load remove bottom panel 3 screws once remove now you have access to pump get towels and bucket oper lint filter and remove debris from inside ,,,,, and that its F2 long drain,,,,,,

Hi! ricksmith
What is the first three digits of the model number.
The he4t I have reference to does not have a "F" code error. Most of the codes are two digit, PF, F1 to F9 etc.
You could try: Pressing Pause/Cancel two times to clear code. As well as unplug for 20 seconds. Do you have power fluctuations in your area.
InMrFixIt