Our bosch diswasher on auto wash will stop functioning in middle of the cycle start beeping and there is an icon of a faucet on the display. What does this mean?

I have a Bosch Silence Plus 46 dBA. SHS5AVF6UC/22. ...

JustAnswer https://www.justanswer.com > Appliance Repair
Jul 5, 2021 - What have you tried so far? When I try to start the cycle, the red light on the floor comes on, it beeps, but won't start.
1 answer · Top answer: Hi and welcome to Justanswer. My name is ***** ***** to assist you today. I'm

Why is my Bosch dishwasher beeping and not starting?
Bosch dishwashers are designed to beep when there is an error. A beep means that your drain is not clogged, and the rest of the parts are functioning as they should. Beeping in the middle of the cycle points to the problem with the control board itself. Find the circuit breaker and turn it off for 60 seconds.

Bosch Dishwasher Error Codes ~ By I-Fix Appliance Repair

rcd units trip from the milliamps that are in a short
it trips the rcd to prevent electrocution and acts in nano seconds besides being a circuit breaker for excessive current
the trip can be from moisture allowing a current leakage to ground or some other simple operation
I suggest that you get in a qualified electrician / bosch service technician to find the reason for the problem rcd

3 things to check...

1. Insure water faucet at the wall is fully turned on.

2. Insure the hose is not kinked.

3. After checking 1 & 2, turn off the water at the wall faucet. Remove the hose at the wall faucet and the washer. Straighten the hose and look down in the side that goes to the washer. There should be a small screen to filter debris. If it is clogged, use a safety pin or straight pin to punch out the debris. Rinse and reattach the hose.

If the above steps show no issues, then your water on/off valve inside the Bosch is shutting off too soon and most likely will need a repairman to fix or replace it.

I hope this helps.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/don_e04c7d10037aa2ce

Replace the circuit board.

Hello,

Welcome to FixYa.

I think can answer your question..."How do you disable the cycle completion signal/beep on the Bosch SHU9915UC dishwasher?"


Follow these steps...

**How to Operate the Cycle Completion Signal**


1. Open door, hold down program button (see
Beeper Table below) and simultaneously turn the unit "ON".


MODEL Program BUTTON

SHU 9950 Delay Start Hours
**SHU 9910-9920 Delicate/Econo** should be yours
SHU 8800/8810 Quick Wash
SHV 6800 Delay Start Hours
SHV 4800 Delicate/Econo
SHV 4300 Delicate/Econo


2. Release program button.
a. For SHV 6803 and SHU9950 models:
The display will blink with a code of "0", "1" or
"2". You are in program mode.

• If the display blinks with a "0", you will hear
no signal (indicates OFF).

• If the display blinks with a "1", you will hear a
LOW volume signal.

• If the display blinks with a "2", you will hear a
HIGHER volume signal.

b. For all other models with the beeper
function:

• If the machine beeps, then the Cycle
Completion Signal has been enabled.

• When you push the button again and it does
not beep, it means that the Cycle Completion
Signal has been disabled.

3. To change the program, press the program
button until the desired setting is selected.

4. Turn the Dishwasher off to take it out of
program mode.

* At the end of a wash cycle, the beeper will sound
off two times, and again every 15 minutes until the
dishwasher is turned off.

Hope this answers your question and provides you with what you needed.

Thank you for choosing FixYa and good luck.

Please take a moment to rate the solution provided and a short testimony if you feel it's warranted, but also let me know if you require further assistance.

Regards,

Macmarkus :)

yes the problem from the heater.

if the sound coming from boiler heater means
1)scaling on the boiler tank(tank to be cleaned).
2)check any loose connection on the heater wire.

looks like a heater failure it statrs to heat at about this time into wash mode.

Dry out the catch pan under the dishwasher. Unplug the unit for 45 min. Repair man said this should reset the unit.

Hi, it seems its about time to replace the motor carbon brushes.
Thanks

OL on my washing machine