My computer sees the device being attached, but i see no video

Sounds like the power supply is either on it's way out or isn't powerful enough to power everything that is plugged in. Try unplugging all usb devices and other attached devices and just power it on with only keyboard and mouse plugged in to see if the computer stays on longer.

click start control panel administrative tools computer management device manager scroll down universal serial bus controllers you could see a yellow question / exclamation mark? ! or a red X

you will need to update/reinstall drivers

right click to reinstall drivers

if you can see your usb drive but its not working

ports(com&lpt)right click update driver if this fails to fix the problem

check the USB leads that attach to the motherboard usually red white green black make sure they are securely seated and have no dust build up on them dust will cause static and a lot of unforeseen problems for a computer and its parts

hope this helps you

Connect the monitor to another computer if possible to eliminate the monitor as the faulty hardware
Shut down the computer. Remove all cables and devices plugged into the computer. Make a note of the port into which your monitor is plugged
Remove the left side panel when facing the front of the case. Unscrew screws or manipulate latches to remove the side panel. This process varies according to the type of case you have. Please consult your manual if you are unsure of how to remove the side panel.
Attach the antistatic wrist bracelet's clip to a metal object, then ******** the bracelet.
Locate your video card. (This will be the card that contains the port with which your monitor interfaces.) Remove the slot cover screw that secures the card into the slot.
Remove any power cables that connect the video card to the power supply.
Pull the card out of the slot. Examine the gold pins to check for any damage. Reseat the card if it physically appears to be undamaged. You should hear a click once the card is secure in the slot
Screw in the slot cover screw. Attach the power cable from the power supply unit, if applicable.
Leave the case open for now. Reconnect only the monitor, power cable and any devices required to boot the computer, then restart the computer.
Shut down the computer again if you receive the "No-input Signal" error message again. Remove any cables and devices you plugged in to restart the machine.
Remove the video card with a spare or replacement by following the instructions above.
Connect necessary cables and devices to reboot the computer, then restart it.
Shut down the computer and remove cables and devices if the display still won't work.
Unplug the power supply's cables from all devices on the motherboard. Make a note of each plug-in so that you can correctly connect all devices with the new power supply.
Remove the screws that mount the power supply. Fit the new power supply into the mounting area, and screw in all screws.
Attach all required power cables to devices connected to the motherboard.
Attach the cables and devices required to start the computer. Reboot.

hope it can help you ma-friend

Imake sure the lead/s that attach to pinnacle are securely seated
t could be a problem with the driver
click start control panel administrive tools ,computer management ,device manager look through all of your devices if you see a yellow question mark?or exclamation mark ! or red x
right click to reinstall drivers or
if you can see your usb but its not working

ports(com&lpt)right click update driver

hope this helps
http://download.cnet.com/%7Bvalue=http://www.download.com/dazzle-dvc-80-2/3000-2118_4-74756.html

if your computer came with a motherboard disc the sound drivers could be on it click start control panel administrive tools computer management device manager scroll to sound,video and game controllers you might see a yellow question mark? Right click to reinstall drivers Click start control panel administrive tools computer management device manager scroll to display adapters + to expand you might see a yellow question mark ? or exclamation mark ! or a red x right click select reinstall drivers also

One bad lead can cause a computer to continue on a cycle or to shutdown or fail to detect your hard drive

Test all leads that attach to your hard drive including electrical extensions,IDE,SATA

the leads from your ((motherboard to your hard drive)) make sure they have a secure connection and are not faulty or just replace them there probably old and faulty make sure all leads that are attached to your drives dvd\cd 3 1/2 inch floppy have secure connections and are not faulty even the electic extensions or just replace them they could be faulty a computer needs its connections to continue its cycle and to have an end so any faulty leads will end up with a computer error

Click start control panel administrive tools computer management device manager scroll to display adapters + to expand you might see a yellow question mark ? or exclamation mark ! or a red x right click select reinstall drivers also you might uninstall the display adapter restart your computer then reinstall the display adapter and its drivers this would apply to the sound video and game controllers to hope this helps

if your computer came with a motherboard disc the sound drivers could be on it click start control panel administrive tools computer management device manager scroll to sound,video and game controllers you might see a yellow question mark? Right click to reinstall drivers Click start control panel administrive tools computer management device manager scroll to display adapters + to expand you might see a yellow question mark ? or exclamation mark ! or a red x right click select reinstall drivers also

One bad lead can cause a computer to continue on a cycle or to shutdown or fail to detect your hard drive

Test all leads that attach to your hard drive including electrical extensions,IDE,SATA

the leads from your ((motherboard to your hard drive)) make sure they have a secure connection and are not faulty or just replace them there probably old and faulty

make sure all leads that are attached to your drives dvd\cd 3 1/2 inch floppy have secure connections and are not faulty even the electic extensions or just replace them they are probably faulty a computer needs its connections to have an end so any faulty leads will end up with a computer error hope this helps don

if your computer came with a motherboard disc the sound drivers could be on it click start control panel administrive tools computer management device manager scroll to sound,video and game controllers you might see a yellow question mark? Right click to reinstall drivers Click start control panel administrive tools computer management device manager scroll to display adapters + to expand you might see a yellow question mark ? or exclamation mark ! or a red x right click select reinstall drivers also

One bad lead can cause a computer to continue on a cycle or to shutdown or fail to detect your hard drive

Test all leads that attach to your hard drive including electrical extensions,IDE,SATA

the leads from your ((motherboard to your hard drive)) make sure they have a secure connection and are not faulty or just replace them there probably old and faultymake sure all leads that are attached to your drives dvd\cd 3 1/2 inch floppy have secure connections and are not faulty even the electic extensions or just replace them they are probably faulty a computer needs its connections to have an end so any faulty leads will end up with a computer error hope this helps don

Hi,

To delete videos from your YouTube account, open the 'My Videos' page by clicking this link:
http://www.youtube.com/my_videos?feature=mhum
(You can also open the "My Videos" page by clicking the Arrow button next to the "Sign Out" link at the top-right of the YouTube page and then select "My Videos" from the drop-down menu. (See attached image)



A list of all your uploaded videos will open. Click the checkbox next to the videos which you wish to delete and click the Delete button at the top. (See attached image)



Hope this solves your problem. For more help and clarifications, please feel free to reply to this post.

Thanks for using FixYa.

it seems that you havent followed the installation procedure correctly. most of the devices comes with written installation directions.
now uninstall the drivers form your computer, disconnect the device from the computer and reboot the computer. then install the driver of the device first(at this point dont attach the device to the computer) after installing the driver than attach the device to the computer. the operation system will automatically detects the device and install it, or if you've asked for the driver click the automatic dectect and install button.

Firewire works fine under Vista, but it's quite possible your USB to Firewire bridge doesn't have proper Vista drivers. You wouldn't expect Vista to include these, they would be installed from a disc that came with your adaptor. USB to Firewire is a questionable option at best... there are often problems with it. You may be better off with a PC-Card or ExpressCard solution, if the laptop is your only computer.

Also, when the camera says "DV IN", it's expecting video from the PC to be sent to it, it's not in capture mode. Most camcorders must be in either "play" mode, or a special "link to PC" mode in order to even be recognized by Windows (any version) as a video input device.

However, until you resolve the issue of supporting your Firewire device in Vista, nothing the camcorder does will be an issue yet. You should check the documentation that came with your USB to Firewire device, the driver disc, etc. for information on Vista support.