JVC LT-32X575 32 in. HD-Ready LCD Television Logo

Related Topics:

A
Anonymous Posted on Jun 07, 2017
Answered

I have a JVC LT 26X575 that will not accept remote input for any function, but using the buttons on the TV allow the menu to be achieved and the sound to be raised or lowered. In TV mode it comes on on channel 2 and the channel cannot be changed so I can not get the cable input to work (needs channel 3). When feed from the cable box using 3 wire audio and picture cord, can get a wonderful picture on Video 1 channel, but remote still will not talk to the TV. Please help

Answer This Question

1 Answer

mikemail1

Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
New Friend:

An expert that has 1 follower.
Night Owl:

An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert 95 Answers
  • Posted on Jan 04, 2018
mikemail1
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
New Friend:

An expert that has 1 follower.
Night Owl:

An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

Joined: Aug 25, 2010
Answers
95
Questions
0
Helped
30543
Points
286

Sounds like the remote batteries could be bad or the buttons on the remote need to be cleaned. some JVC TV remotes, I'm not familiar with this particular one though, can be cleaned using a clean pencil eraser. Be careful opening the remote because some parts can fall out or you can damage the connections to the LED emitter that sends the signal to the TV. Also the solder connections on that LED could be bad.

5 Related Answers

Anonymous

  • 60 Answers
  • Posted on Dec 10, 2008

SOURCE: Remote control for JVC TV stopped working

1 if this new ordere it is exacly the same that should work when i say exacly that must have only the same button on it
2 you should try to take off the cover to that old remonte and try to clean the taste and then the change battery clean suport to battery wash your rubber taste and put all togheder and should work if that not hapened the problem it is from inside tv

and to that new one see if you have a shift buttun on it and push that or push tv button and try again should work

Ad

Anonymous

  • 1779 Answers
  • Posted on Feb 04, 2009

SOURCE: JVC LCD TV LT-42X688-powers on, blank screen. no picture,no sound

You most definately have bad capacitors in the power supply. try and get it repaired as soon as possible, not an expensive repair that iv'e seen.

Anonymous

  • 1 Answer
  • Posted on Mar 29, 2009

SOURCE: JVC LT 32E479 UNABLE TO SWITCH ANY CHANNELS

go to menu select TV settings select add a channel  In the scan boxes  type 1 and 3 or what every you have your Satellite set to  Then hit start scan  The TV will come on reset to channel 3. 

Anonymous

  • 105 Answers
  • Posted on May 06, 2009

SOURCE: JVC LT 42x688 no picture just sound

Sorry, this has no easy fix. The good news is you do not need an LCD Panel. The bad news is the Video Processor has a problem.
This TV has x3 Boards. The one you should replace first is the one in the middle. If this doesn't fix it, try the one on the right. The Part #s are on the Boards if you wanna try ebay.

Anonymous

  • 105 Answers
  • Posted on May 27, 2009

SOURCE: No Picture

I am deeply sorry but you will need to replace the backlight bulbs. These are not available.

Look on Ebay for a 32" JVC with a broken LCD Screen. Buy it and use these bulbs to fix your TV. I am sure there will be a few good ones in the broken TV. It's that or list it on Ebay for $50 and expect to get about 200-300.

LCD Panel repair for this problem is $500 for parts so you are stick with repair yourself or sell.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I have a jvc tv model no. Lt-26x575 with no remote. How do i scan for antenna tv
Without a remote control, you can't. If you wish to buy its original remote control, contact the authorized service centre, or authorized dealer to your device brand. They can either give you a genuine remote control to your device, or can direct you, from where can you purchase a suitable one.
To select a proper universal remote control, you should know about the number of digits to its set-up codes. There are 3 digit, 4 digit, 5 digit, 2 digit and even single digit codes, to some brand devices. After confirming this, check the sites linked here. Both the sites have set-up code list and set-up procedure to many popular brand remote controls. Check which brand remote control has set-up code/s to your device brand, and buy that one according to availability. Brand name of the remote control isn't a matter, but it should have set-up codes in its code list, to the device brand you have.
Please note: Every new universal remote control will have set-up code list, and set-up procedure along with its pack. Never accept a remote control, that hasn't both of this. For more details about the set-up codes, visit the sites.
http://electrohelponline.blogspot.com/
http://remotesearch.blogspot.com/
Universal remote controls are available at most of the electronic spare part selling shops. Visit some on-line sites too, which deals with electronic spare parts.
Read full answer
Nov 04, 2016 • JVC LT-26X575 26 in. LCD HDTV
tip

JVC LT-26X575 LCD TV Manual Download
Download JVC LT-26X575 LCD TV Manual

16a54a8.jpg

Would you like to review the features of the JVC LT-26X575 LCD TV ?

Have you lost your JVC LT-26X575 LCD TV Owners Manual?

Would you like a digital, searchable, pdf version of the JVC LT-26X575 LCD TV Users Guide?

Follow this link (& click FREE) to download a pdf version of the JVC LT-26X575 LCD TV documentation.

I hope that helps.
___________________________________________
Read full tip
on Jul 03, 2010 • Televison & Video
tip

JVC LT-26X575 LCD TV Manual Download
Download JVC LT-26X575 LCD TV Manual

16a54a8.jpg

Would you like to review the features of the JVC LT-26X575 LCD TV ?

Have you lost your JVC LT-26X575 LCD TV Owners Manual?

Would you like a digital, searchable, pdf version of the JVC LT-26X575 LCD TV Users Guide?

Follow this link (& click FREE) to download a pdf version of the JVC LT-26X575 LCD TV documentation.

I hope that helps.
___________________________________________
Read full tip
on Jul 03, 2010 • JVC LT-26X575 26 in. LCD HDTV
0helpful
1answer

XCAN'T FIND THE BUTTON TO RUN CHANNEL AUTO SCAN
First make sure that the Source is set to TV and a good antenna/coaxial cable is connected to the TV. Use the Input button on the TV (to the left of the power button) or the Input Select button on the remote. Use the up/down arrow keys to navigate through the source list and press Enter to select that choice. (On the TV, the Input button is the Enter button.) Next press the Setup/TV Menu on the remote (or Menu on the right arrow button or Enter. Then go down to Auto Ch Memory and press the right arrow or Enter. With the up/down arrows, navigate to Signal Type and set that to Air (for OTA channels) or Cable with the left/right arrows. Now navigate to Automatic Search and press the right arrow or Enter. Wait for the scan to be completed.

I hope this helps. The steps are shown in the manual for the LT-19D610 on page 18. The manual is available from JVC on the product page: http://support.jvc.com/consumer/product.jsp?modelId=MODL028825 . The direct link to the manual is http://resources.jvc.com/Resources/00/01/47/J55D0221B.pdf .

Cindy Wells
Read full answer
Dec 05, 2015 • JVC LT-19D610 19" 720p 1366 x 768 35000:1...
0helpful
1answer

PC HDMI W4201C 42 CONNECTION
Hi Caleb,
To resolve this, please perform the following steps:

  • Turn off the TV and unplug the power cord
  • Connect the HDMI cable to the HDMI port of your laptop.
  • Connect the other end of the HDMI cable to the HDMI input on your HDTV
  • Connect your device using the HDMI connector (Refer to image below)
d607e207-edde-4a6c-976e-afe231ed034f.jpg

  • Plug in the power cords for the TV and Xbox
  • Turn on your TV and Xbox
  • Enter the TV Menu and select Setup (Refer to the image and steps mentioned below)
9ab5d76e-dbfd-4c03-9291-14127e474b68.jpg

  • To enter the TV Menu, press the Menu button on Remote control
  • Use the left and right buttons (volume buttons) to move between the icons

Select correct input source
  • Input allows you to select the proper source based on how you have your TV and video equipment connected.
  • Press Input on the remote to go directly to the Input Select menu
  • Select HDMI 1 or HDMI 2 (Refer to image below)
bd6ef790-448b-4623-945e-162c7c862e64.jpg

If the TV does not work, please follow these steps:

Verify the PIP/POP/PBP function is disabled ( PIP/POP/PBP Compatibility - The only input sources that cannot work together are HDMI with HDMI)
  • Press the Menu button on the remote control or TV
  • Use the Left and Right arrow buttons (Vol +/-) to select PIP/POP/PBP, and then press <Enter>
  • Use the Up and Down arrow buttons (Ch Up/Ch Down) to select PIP/POP/PBP/OFF
  • Use the Left and Right arrow buttons to select Off

If issue is still persists, please move to the next step

Reset the TV current input to its default configuration
  • Press the Menu button on the remote control or TV
  • Use the left and right arrow buttons to select Setup, and then press Enter/OK
  • Use the Up and Down arrow buttons to select Factory Reset, and then press Enter/OK
  • Select Current Input Setting and press Enter/OK
  • Re-check the TV functionality
Read full answer
Feb 19, 2014 • Dell W4201C 42 in. Plasma HDTV
0helpful
1answer

TV will not recognize the remote control I suspect an IR issue within the TV
If you point a mobile phone camera toward the output of the remote, you will see if it works or not.
Hope that helps.
Read full answer
Mar 01, 2011 • JVC LT-26X575 26 in. LCD HDTV
0helpful
1answer

Original remote lost. have universal remote. cannot program TV
On the right hand side of this television there are panel buttons. It appears that your son in law knocked the tv out of the correct input. Press the input button in order to cycle through the 5 inputs. Typically pressing the input button on the side panel of a television and pressing it again and again and again will make it change inputs. Universally the buttons on the tv panel function as follows: Channel up moves the cursor up. Channel down moves the cursor down. Volume + moves the cursor right. Volume - moves the cursor left.
Hope this helps
Read full answer
Apr 28, 2010 • JVC LT-42E478 42 in. LCD Television
2helpful
2answers

JVC 40 inch LCD digital inputs (1 and 2) no longer works. Standard video and component cable inputs work, but not HDMI. Please help
This TV has a sensor that deactivates the inputs when light is sensed. perform this procedure to correct it:

1. press "Sleep" button on the remote
2. while "Sleep timer 0" is showing, simultanuously press "display" and "video" button on the remote
3. you should be in the Service menu of the TV....if not you should do the steps again
4. select "self check" from the displayed options.
5. when the "self check" menu is displayed, Power off the TV.
6. unplug and replug the TV.
7. Check the digital input.

if the input never worked for you, it is possible that you have the DVD/Bluray/whatever set up incorrectly. I don't think this TV accepts 1080P resolution so make sure it is set to 1080i or lower
Read full answer
Jun 23, 2009 • JVC LT-40X776 40 in. LCD HDTV
3helpful
1answer

REmote control RM-C1257G not working even after trying new batteries
Try this

1. Get camera phone
2. set camera phone to to take picture
3. point remote at camera and look at the camera display
4. press buttons on the remote, you should a light from the Remotes IR.
5a. If NO light is seen, your remote is broken. you can try replacing the batteries to double check
5b. if Yes, light is seen. Your remote is working and you may have a problem with the TV.

As a double check, get a remote you know is working and try the same thing to verify that you are checking the remotes correctly.
Read full answer
May 27, 2009 • JVC LT-26X575 26 in. LCD HDTV
1helpful
1answer

Remote control for JVC TV stopped working
1 if this new ordere it is exacly the same that should work when i say exacly that must have only the same button on it
2 you should try to take off the cover to that old remonte and try to clean the taste and then the change battery clean suport to battery wash your rubber taste and put all togheder and should work if that not hapened the problem it is from inside tv

and to that new one see if you have a shift buttun on it and push that or push tv button and try again should work
Read full answer
Dec 10, 2008 • JVC LT-26X575 26 in. LCD HDTV
Not finding what you are looking for?

View Most Popular

LT-32X575 32 in. HD-Ready LCD Television

  • Televison & Video

Related Question

I have a jvc tv model no. Lt-26x575 with no remote. How do i scan for antenna tv

  • JVC LT-26X575 26 in. LCD HDTV

Related Topics

297 views

Ask a Question

Usually answered in minutes!

Popular Questions

JVC 42 inch LCD HD TV has no picture or sound

JVC LT-42X579 42 in. LCD TV

I have multi colored vertical

JVC LT37XM48 LCD TV

JVC LT-32P679 Blinking Power Light, Automatic Shutoff

JVC LT-32P679 32 in. LCD TV

Trying to connect playstation 3 to my tv having no success

JVC LT-37X776 37 in. LCD HDTV

I turn on the T.V. and the blue light is blinking

JVC LT42P789 42 in. LCD TV

Check Out the Latest HD Televisions Report
Check Out the Latest HD Televisions Report

View all Fixya Reports

Top JVC Televison & Video Experts

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

matt martin
matt martin

Level 3 Expert

1259 Answers

Grubhead
Grubhead

Level 3 Expert

5755 Answers

Are you a JVC Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...