Question about Jenn-Air 34 in. Expressions CVGX2423 Gas Cooktop
We have an Jenn-Air gas range, it has the problem that it's getting difficult to start the fire while the igntter keeps the clicking sound, and producing sparks. We did smell the gas being released at the same time.
Sometimes the igniter works.
We also have the problem of all 4 igniters keep clicking, when one of the stove is lit.
01/26/09 My wife decided to give our Jenn-Air a good cleaning. With lot's of soapy warm water she pulled the knobs off and washed under each of them not realizing excess water was now running down the inside of each control knob shaft. The igniter immediately began clicking away as it was being shorted by the conductance of the water now inside of the switch. I had to remove the cover (2-screws) to access the control switches but that is all I needed to do do in order to have clear access. Using her hair dryer it took about 5 minutes of warm air blowing down each of the shafts until the water evaporated and the clicking stopped. Wahla. The old Jenn-Air is back to working order again.
Posted on Jan 27, 2009
I followed Beaker52's advice and it worked! I also have a Jenn - Air stove where the igniter was clicking, gas was flowing but the burner wasn't lighting. The manual was useless but this forum was very helpful. I plugged in the hair dryer, aimed it right at the igniter from 2-3 inches away and let it blow hot air for about 5 minutes. The burner now lights within a second or two, the way that it should. At the very least this is worth 5 minutes of your time to try.
Posted on Jun 07, 2009
Just had the problem of continuous clicking after the stove lit. The probem is in your electrical wiring. It is not grounded correctly. The way the sensor works to let the controls know that the stove is lit, is by relaying a signal to the electrical box and then back to the control unit. If the electric box is not grounded correctly it can not relay the signal.
Posted on Mar 18, 2009
Well none of these fixes apply to my case. i can see it is a weak spark (not blue) even after cleaning. Seeing as to the high costs of the electric ignition module, I'm just going to go buy a hand held welding flint lighter and make life easier.
If I was inspired, I'd probably find some better ignition system and retro fit this whole thing for 1/2 the costs of replacement parts.
Posted on Jun 15, 2010
Thanks mrroyal111! -- I had clicking after the burners were burning. Problem was that I'd removed the inner ring during cleaning and did not put it back properly. There are little nubs that must be lined up properly. If you don't, ALL the burners can start to act wonky when you try to ignite them. Problem solved.
Posted on Mar 04, 2010
Be sure that you have the groove in the burner head over the igniter. Surprisingly you can put the burner head on with the groove in another place. I did that.
Posted on Feb 04, 2010
Try reversing the AC wires, white to white, black to black solved my problem.
Posted on Oct 19, 2009
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Here is a tip that I wrote that will help figure out why the burner spark keeps on clicking...
Gas Range Repair Burners Keep on Clicking
Jan 27, 2011 | Jenn-Air Cooktops
Jun 16, 2010 | Jenn-Air 36 in. CCG2523 Gas Cooktop
May 23, 2010 | Jenn-Air 30 in. JGD8430A Gas Cooktop
May 02, 2010 | Jenn-Air 34 in. Expressions CVGX2423 Gas...
Mar 25, 2010 | Jenn-Air 30 in.JGD8430ADS Gas Cooktop
Mar 09, 2010 | Jenn-Air 30 in. CVG4280 Gas Cooktop
Mar 01, 2010 | Jenn-Air 36 in. CCGP2720P Gas Cooktop
Dec 18, 2009 | Jenn-Air 35 in. JGC9536 Gas Cooktop
10,586 people viewed this question
Usually answered in minutes!