Motherboard problem in a KEMI300wbl3.After a powersurge the clock will set and the oven timer will work but the keypad resets to 0000 when I press start

To set my Russell Hobbs Microwave clock, I found....press and hold timer/clock button, untill it comes up with 24 hr, ( am guessing press it again to set to 12 hr, but wasn't chancing it lol) use numbers to set time, then press timer/clock button again! Hope that helps someone!

To set the clock, you need to press Timer/Clock twice. Then press the 10 Min keypad several times until you get to the correct hour. Then press the 1 Min keypad as needed to get to the closest 10 minute period below the current time. Finally press the 10 Sec keypad several times to reach the current time. Then press Timer/Clock once to exit the time set feature.

Panasonic has the manual for the NN-E271WM on their downloads page: http://www.panasonic.eu/Downloads/en_GB/popup.html . Enter the model number and then click View. You will need to accept the Panasonic Terms Of Use and click View again. The direct link to the manual is currently http://tda.panasonic-europe-service.com/docs/2z5845f124z3z39cabz656ez706466z25z9709ff8b3ba329b0c218b9bf248a6442e93022b3/tsn3/data/ALL/NNE281BMBPQ/OI/912715/NN-E271WME281BME281MM.pdf . See page 21 in the manual (23 in the PDF) to see the procedure.

I hope this helps.

Cindy Wells

To set the clock, press
"Clock"
once
or
"Timer/Clock"
twice
(depending
on your keypad)
.
The colon symbol (:) will flash.
Enter time of day.
The time appears
in the window; the colon continues
to flash.
Press
"Clock"
or
"Timer/Clock"
again - colon stops flashing; time of
day is set !

on most: press clock, press numbers on keypad, press am/pm, press clock(on some press start). timer: press timer, press numbers, press timer.

According to the manual this is how to set clock.

To set the clock, press "Clock" once or "Timer/Clock" twice (depending on your keypad).
The colon symbol (:) will flash.
Enter time of day. The time appears in the window; the colon continues to flash.
Press "Clock" or "Timer/Clock" again - colon stops flashing; time of day is set.

If you need the manual it is on link below.

http://service.us.panasonic.com/OPERMANPDF/NNH624-SET%20UP.PDF

Good Luck

Operating functions:
To set the clock, press and hold the clock/timer button for three seconds. A clock icon will appear on the left side of the screen. Input the time using the numerical buttons and then click the clock/timer button to save the time.
To set the timer, press and release the clock/timer button so that the display shows all zeroes. Enter the desired time using the keypad. Press start/stop to start the countdown. The countdown may be paused by pressing the stop/start button and resumed by pressing the same button again.
When countdown is complete, timer will beep continuously for thirty seconds and display will flash. Timer will then beep every ten seconds for ten minutes until the stop/start button is pressed.
This timer will also time up to time activities. To start count up, press clear/memory so timer reads all zeroes. Press stop/start and a plus sign will appear on the right side of the screen as the timer begins counting up.

normally you look for the clock ot watch icon. Pressing it once will give you the option for 24 hours setting. Press it twice and it will give you the opportunity to set to 12 hours setting. Using the no. keypad, punch in the time and then repress the clock icon again.

This is the generic instructions to set the clock. I have visited the sanyo site to aquire a owners manual with no success in locating one. This being said, here are the instructions.

1. Unplug the unit for a minute then plug unit in.
2. Press the clock (clock/timer) button once.
3. Using the keypad, input the time you wish to set.
4. Press the clock (clock/timer) button once.
5. Press the stop/clear button, Time should remain.

Hope this works, if not, let me know.

Please take the time to give this solution a fix ya rating.

clarkco

Pressing "timer/clock" button 4 times turns on and off demo mode.

look on the back panel for any hole with a "RESET" label next to it. insert a small pin to reset your microwave