What does the code F35 mean?
F-35 is a failed analog pressure switch. A common problem these days.
I have a replacement how to video HERE
If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61
HELLO.F35 IS A ERROR CODE WHICH NEEDS THE ASSISTANCE OF A WHILPOOL SERVICE AGENT.THE CONTROL BOARD MIGHT NEED TO BE REPROGRAMED BEFOR YOU CONSIDER REPLACING IT.GOODLUCK.MOHAMED
Before calling a repairman, check the pump strainer to see if it is clogged or has coins or a sock blocking it. The pump strainer is behind the lower front panel. The front panel comes off by removing the three torx (star type) screws located underneath the panel. The pump strainer cover is white and about 3" in diameter and unscrews by hand. Here is a link to a picture:http://neighboursappliance.com/2008/01/d...
I have a Whirlpool Duet (steam model, built in 2007). Getting the ever common "sud" and "F35" error. Done all the typical research. Took top and bottom off. Everything clear. Have not taken back off and looked at the actual "air trap". But, I can blow throw the black tube that connects to the pressure sensor switch. All research seems to point to the notion/belief that my sensor is bad.
×
Outside the normal analog pressure sensor (APS) / hose checks...
Another cause for the F35 and SUD error could be your CCU (control unit). There are components that seem to fail over time and cause the F35 and SUD errors. You can replace those components yourself now...
See f35 error for more information.
I hope this helps and let me know if you have any more questions.
Replaced the $109 pressure switch for my Kenmore he3t, and sorry to report here is no change with the new pressure switch. I ran the diagnostic and it makes it through the C:00 test fine and then throws a F35 error before it gets to the C:01 test. I don't know if I'm going to have to end up building this thing part by part.
Replaced the $109 pressure switch for my Kenmore he3t, and sorry to report here is no change with the new pressure switch. I ran the diagnostic and it makes it through the C:00 test fine and then throws a F35 error before it gets to the C:01 test. I don't know if I'm going to have to end up building this thing part by part.
Must be something wrong with the control board.
×
Hello.
The F35 alert code on your Whirlpool washing machine indicates a problem with the drainage system. This could be an easy fix, or it could require a complete replacement of the water discharge pump. Before you can determine how to correct the issue, you must complete the troubleshooting process.
Thanks.
SOURCE: F35 flashing
if it is less than one year old call for service it should be covered. if not take the kick panel off and locate the tech sheet it is either in the kick panel or in the cabinet to the right. it will give you a list of error codes find out what it means and let me know thanks
SOURCE: Whirlpool duet front load washer flashes F35 shortly after start
Sud= The unit has sensed there is too many suds in the unit it will
flush and pump out for 5 min and restart on its own..This is caused by
too much soap use..
From the book :
SUD Code=
If too much detergent was used:
—Run the unit through a Rinse/Spin cycle.
—Run a Normal cycle without adding any detergent.
This should clear the unit of the excess detergent.
1. Check the drain hose and make sure it is not plugged
or kinked.
2. Unplug washer or disconnect power.
3. Check wire harness connections to the drain pump,
pressure switch, and Central Control Unit (CCU).
4. Check/clean drain pump filter of foreign objects.
5. Plug in washer or reconnect power.
6. Check drain pump.
7. Check the pressure switch.
8. Verify CCU operation by running a Diagnostic test or any
cycle.
Hello & Welcome to FixYa
F35 error means that there is some sort of issue
with the steamer electronic board and analog pressure sensor has gone bad.
Check that the hose is firmly attached with the washer and is not blocked. You
can also check the water level pressure switch operation. Please get back to me
if you have any other questions.
Kevin
Hello & Welcome to FixYa
F35 error means that there is some sort of issue
with the steamer electronic board and analog pressure sensor has gone bad.
Check that the hose is firmly attached with the washer and is not blocked. You
can also check the water level pressure switch operation. Please get back to me
if you have any other questions.
Kevin
Hello & Welcome to FixYa
F35 error means that there is some sort of issue
with the steamer electronic board and analog pressure sensor has gone bad.
Check that the hose is firmly attached with the washer and is not blocked. You
can also check the water level pressure switch operation. Please get back to me
if you have any other questions.
Kevin
2,296 views
Usually answered in minutes!
http://www.youtube.com/watch?v=4wjhrB-4f...
×