Question about Maytag PAV2300 Top Load Washer

1 Answer

I was given a Maytag Supreme Model PAV2300 awa by my son. How strong is the pump in the machine and how high can the waste water be pumped?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,341 Answers

For most all wasing machines the maximum height is 8 feet

Posted on Aug 05, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a maytag pav2300 pump will not pump


see this causes:
It spins, but doesn't pump
drain line is clogged, remove some sock with pliers+test the pump for defective propeller, and replace DO NOT REPAIR
It doesn't spin or pump
frozen pump puller +and replace the pump
It pumps, but the water returns
if the drain hose reach more about 4 inches, cut of the excess
if the hose is lower, install air/gap siphon break assembly
see the diagram.
God bless you


6_29_2012_12_57_04_pm.gif6_29_2012_12_57_19_pm.gif

Jun 29, 2012 | Maytag PAV2300 Top Load Washer

1 Answer

Can't find where the clutch goes on a Maytag Performa PAV 3300, is it in the transmission?


This washer is a single belt driven model that uses a thrust washer system to release the brake when the motor reverses. In wash mode a 200# spring locks the tub place while the transmission agitates the clothes. The pump cannot remove the water in this direction. In spin mode the the brake is released and the water gets pumped out. Here is a great pictorial that shows how to replace the kit along with a Maytag single belt washer service manual.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Oct 08, 2011 | Maytag PAV2300 Top Load Washer

1 Answer

Pulley and bearing removal of water pump on a maytag pav2300aww washing machine


the pulley and bearing are not removable on your pump. it is replaced as a complete pump assembly.

Feb 07, 2010 | Maytag PAV2300 Top Load Washer

1 Answer

I m using maytag pav2200agw after fill the water washer is working fine but during the spin dry cycle water pump does pump out the water and start spin but the tub is not moving its not working propperly...


I WISH I HAD SOME ANSWERS ON THIS ONE, BUT IT SOUNDS LIKE YOUR PUMP MIGHT NEED REPLACING. HOW OLD IS YOUR WASHER? IT WOULD BE CHEAPER TO BUY A NEW WASHER. BUT IF IT IS THE PUMP, THEN YOU CAN BUY A NEW PUMP FROM WHERE YOU BOUGHT YOUR WASHER. GOOD LUCK.
RODNEY

May 12, 2009 | Maytag PAV2300 Top Load Washer

1 Answer

Maytag SAV 3652 AWW Washer: During spin cycle, burning smell occurred while making unusual noise. (For months, major squeaking during agitation).


Bad water pump. Replace water pump.tip machine back,Look under machine, remove belt, turn pump by hand, if not spinning freely replace pump.

Mar 23, 2009 | Maytag PAV2300 Top Load Washer

1 Answer

Leaking water for washer machine


Check your drain, drain hose (make sure the clamp is tight) and check the pump to make sure that all hoses are attached properly

Feb 12, 2009 | Maytag PAV2300 Top Load Washer

1 Answer

Washer spins freely but clothes remain very wet


The two possibilities of which come to mind are, something in pump slowing the water outlet, belt loose or needing replacement. Sometimes an article gets over the barrell and sucked into the pump still allowing some water to pass by, but the belt needing to be replaced would prably be my first check. both need Power disconnect then cabinet panel pulled to view both the pump and belt

Feb 09, 2009 | Maytag PAV2300 Top Load Washer

1 Answer

Washer noise


Bad pump. Tip the machine back and remove the belt. Turn the pump by hand and check if it is locked up.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Jan 10, 2009 | Maytag PAV2300 Top Load Washer

Not finding what you are looking for?
Maytag PAV2300 Top Load Washer Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...