20 Most Recent West Bend 41036 Mixer - Page 4 Questions & Answers

Question edited for a lot more clarity. Time for a new one. Nearly all parts are obsolete. https://www.ebay.com/itm/266100009365?epid=66794889 Parts Suppliers. I checked 3 of them https://www.google.com/search?q=EHC650+parts ..

There are several potential reasons why your KitchenAid dough mixer might be shutting off. Here are a few possible causes: Overheating: If the mixer has been running for an extended period of time, the motor may overheat and shut off as a safety precaution. In this case, you should allow the mixer to cool down for a while before using it again. Faulty wiring: If the mixer is shutting off when you turn it on or when you change the speed, there may be a problem with the wiring. You should check the wiring to see if there are any frayed or damaged wires that could be causing the issue. Clogged air vents: The mixer may shut off if the air vents are clogged, as this can cause the motor to overheat. You should check the air vents to make sure they are clean and unobstructed. Failed motor: If none of the above issues are present, the problem could be with the motor itself. A failed motor can cause the mixer to shut off, and it may need to be replaced. If you are not comfortable troubleshooting the mixer yourself, you should consider contacting KitchenAid customer service or a professional appliance repair service for assistance.

Hi, This sounds like it's a portion of the whole product. If you want that, you might need to arrange an order through nuwave or one of it's manufacturer partners that focuses on the plastic enclosure tha that you've mentioned. If that does not work, then you can reach out to a commercial kitchen product distributor to help with find the part. To find one, you can check on the back of your kitchen product boxes . They sometimes show a "distributed by" phrase in those areas. Thank you.

Tip it on its side and spray it with kitchen cleaner spray. Wait 5 minutes and try again. It is probably gummed up from a messy cake job. FULL 'make model (what it is)' in all questions please, first 3 words. ..

Unfortunately not available anywhere online. Check eBay once every couple of weeks. https://www.google.com/search?q=Cooks+sm248+manual ..

Question edited for full 'make model (what it is)'. There must be a spring in the base that helps the top rise when you depress the button. You will need to remove the base. The manual doesn't mention anything and there is no Service Manual https://www.manualslib.com/manual/1021018/Hamilton-Beach-63390.html?page=5#manual Very limited help here apart from JustAnswer dot com https://www.google.com/search?q=hamilton+beach+model+63390+mixer+tilt+button+not+working ..

Hi, apply some cooking oil to where the parts are connected. If that fails, please submerge the parts in a bucket of or tube of water and attempt to detach them from each other. If all else fails, please reference the manual to ensure that you've not missed a detachment procedure. Thank you.

Hi, The mixer looks to be an antique so you might start with Ebay to find that specific mixer part. Thank you.

The sparks are generally seen where the carbon brushes meet the copper commutator on the motor spindle. This is actually fairly normal. You can lessen it by spraying with some light machine oil, but eventually you will need to replace the carbon brushes.

Impossible to guess what make and model you have! Google make model replacement beater https://www.google.com/search?q=Moulinex+model+replacement+beater ..

Hi, If you call the glue manufacturers, they might be able to direct you to a substance that can dissolve the glue that was applied. Thank you.

There is a little spring clip where the beater is inserted. Disasemble and use some pliers or such like to gently squeeze the clip closed a little. Be careful not to close it up too much.

Question edited for clarity, two question made into one. Duplicated post deleted. Refresh the page to see your question published. Turn the mixer upside down and spray WD40 into the beater holder holes. I think there is a ball bearing detent that hold the beaters and it is probably seized. Leave for a couple of hours and spray again for another couple of hours. https://www.google.com/search?q=Hamilton+Beach+025+HB+10+speed ..

Question edited for clarity. Unit has two maker badges. Any place that services Hobart Mixers will service yours https://www.google.com/search?q=hobart+mixer+service+london+england A.S. Catering seem to be the sales agent for them. https://www.google.com/search?q=22HI-B%20service ..

I expect 4 years later, you managed how to do it :>D Your post attracted spam which was removed, so it brought your question back to the top. It is a pity Chef Andrew didn't see it then! Spray all around the gap between bowl and base with WD40. Then use brute force. Next time, rub a little Vaseline around the surfaces that lock the bowl in place.

When your Grundig start flashing it's 99% stop position switch fault. It can be located in opposite side of speed control board.
You can simply open your mixer, remove speed control board and inject contact cleaner (or similar) directly to holes od black switch. I used medical injector.
Of course better solution is replace switch - it cost few dollars for ten. But in this case you can apply DIY skills. Nothing hard.

Give me the serial number,also hobart does'nt release their service manuals to the general public.However if you goto hobartcorp.com type in your model which is a d300 and you can access an exploded view of the parts.I work for hobart and service these mixers often.Any questions let me know.

Take a 4 foot length of string and put it through the loops of the stuck beater. Tie the end of the string in a knot. Put the loop of string under your foot and hold the body of the mixer and pull.