20 Most Recent AT&T 1818 Corded Phone - Page 7 Questions & Answers


Ebay is usually a good place to start, Good Luck :)

AT&T Lands... | Answered on May 14, 2016


The model number for your cordless phone is on
a small sticker underneath the battery inside the
handset. Entering this number at
www.manualslib.com will allow you to
get a free copy of the original owners' manual.
Good luck!

AT&T Lands... | Answered on May 12, 2016


1. To de-register the orphaned handsets from their old base:
When the orphaned handset says "Connecting..."
enter *331734 [menu]
and it will soon beep and display "Not registered"

2. To register the new handset to your base:
press the "Handset Locator" button on the base and hold
it until the "in use" light comes on ( ~ 4 seconds ),
then release the button and set the new handset into
the base phone cradle. After ~ 30 seconds it will beep
and display "Handset #" (next in sequence).

3: Note: the base handles a maximum of 12 handsets.

If your system was fully populated ( ie, a handset is
already # 12 ) you will have to clear all the handsets
from the base and re-register them all in sequence.
( it is the only way to 'rescue' the places occupied
by the lost handsets ).

To clear the base of all registrations:

1. Press and hold the the "Handset Locator" button
until the "in use" light lights and then starts to blink
( ~ 10 seconds ), release the button --
then press it again briefly while the "in use" light
is still blinking.

2. The base will beep and all handsets that were registered
will display "Not Registered"

3. Follow the instructions above for each handset
in turn to re-register them:
press "Handset Locator" ~ 4sec ( in-use light on ),
set handset into the base cradle, etc.

The manual is available from: www.manualslib.com
but does not fully describe these procedures.

Good luck !

AT&T Lands... | Answered on May 12, 2016


1. To de-register the orphaned handsets from their old base:
When the orphaned handset says "Connecting..."
enter *331734 [menu]
and it will soon beep and display "Not registered"

2. To register the new handset to your base:
press the "Handset Locator" button on the base and hold
it until the "in use" light comes on ( ~ 4 seconds ),
then release the button and set the new handset into
the base phone cradle. After ~ 30 seconds it will beep
and display "Handset #" (next in sequence).

3: Note: the base handles a maximum of 12 handsets.

If your system was fully populated ( ie, a handset is
already # 12 ) you will have to clear all the handsets
from the base and re-register them all in sequence.
( it is the only way to 'rescue' the places occupied
by the lost handsets ).

To clear the base of all registrations:

1. Press and hold the the "Handset Locator" button
until the "in use" light lights and then starts to blink
( ~ 10 seconds ), release the button --
then press it again briefly while the "in use" light
is still blinking.

2. The base will beep and all handsets that were registered
will display "Not Registered"

3. Follow the instructions above for each handset
in turn to re-register them:
press "Handset Locator" ~ 4sec ( in-use light on ),
set handset into the base cradle, etc.

The manual is available from: www.manualslib.com
but does not fully describe these procedures.

Good luck !

AT&T Lands... | Answered on May 12, 2016


Hi, this is a major control fault and you may be able to reset the main board by removing the cell battery for 5 minutes. if the issue still exists after the reset, you will need to replace the main circuit board in this unit.

AT&T Lands... | Answered on May 11, 2016


According to the manual starting on page 52, you need to de-register all handsets then re-register the handsets one at a time. The manual covers both cordless model numbers so the handsets should be interchangeable. I have included a link where you can download the manual if you need it.

http://att.vtp-media.com/ecp/documents/product_Product/127/UserManual/1082/cl82209_manual_i3.pdf

AT&T Lands... | Answered on May 07, 2016


That phone is no longer made, however this part became a head ache for them and they had spares for a while, http://telephones.att.com/

AT&T Lands... | Answered on Feb 06, 2016


All machines have controls for deleting messages. Read your ****** manual.

if no manual go to manufacturer web site.

AT&T Lands... | Answered on Nov 16, 2015


For a better explanation you should look up your user's manual, if warning is documented.
My WILD Guess is that warning appears when you need recharge your batteriy or maybe when battery's voltage/amperage rating is getting too low and probably you need to replace it.

AT&T Lands... | Answered on Oct 05, 2015


The phone gets it power from the network line or ISDN
if its not getting power from the telephone line it does what you describe

try the phone on a line that proven to work and let me know

thanks

rene

AT&T Lands... | Answered on Sep 25, 2015


  • Hit the menu button
  • Find Ringtones
  • Select the Ringtone you want
Hope This Works

AT&T Lands... | Answered on Jul 08, 2015

Not finding what you are looking for?
AT&T 1818 Corded Phone Logo

34 questions posted

Ask a Question

Usually answered in minutes!

Top AT&T Lands Phones Experts

Cindy Wells

Level 3 Expert

6063 Answers

Ekse

Level 3 Expert

13434 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you an AT&T Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

AT&T Lands Phones

  • AT&T Lands Phones

Most Popular Question

need manual amp t 1818 telephone

  • Lands Phones
Loading...