20 Most Recent
Williams-Sonoma Nespresso U Espresso Maker with Aeroccino Plus Automatic Milk Frother, - Page 8 Questions & Answers
Drip Tray stuck inside our Jura s8 coffee machine
To reset your Jura S8 coffee machine and remove the stuck drip tray, you can try the following steps:
- Unplug the coffee machine and wait a few minutes for the internal components to cool down.
- Gently try to wiggle the drip tray to see if you can loosen it from its stuck position. Be careful not to force it, as this could damage the coffee machine.
- If the drip tray is still stuck, you can try resetting the coffee machine. To reset the machine, you will need to locate the reset button or switch. This may be located behind the water tank, under the machine, or in the control panel. Consult the owner's manual for the exact location of the reset button.
- Once you have located the reset button, press and hold it for a few seconds until the machine resets. This may cause the drip tray to release and be able to be removed.
My iCoffee single cup brewer won't brew anymore.
There is more you can do besides descaling. Mine quit dispensing water a couple of weeks after descaling (first descaling in 6 years of use). I figured due to age the pump might be shot until I thought of the Keurig we have at work which will stop working and tell you the needle is clogged. So, I went into and up the needle a couple of times with dental picks-the ones that have brushes at the end. They came out of the needle pretty gunked up. I tried the machine and within the cycle it dripped some water and coffee grounds. I cleaned the needle a second time and this time the water flowed as it should. Works good as new now. So try this before you finally give up on yours.
The Neff C77V60N2/08 coffee machine does not turn on. There is a 220v voltage at the output of the machine's power switch.
The Neff C77V60N2/08 coffee machine does not turn on. There is a 220v voltage at the output of the machine's power switch.
If your Neff C77V60N2/08 coffee machine is not turning on and you are getting 220V at the output of the power switch, it is possible that there is a problem with the internal components of the machine. Here are a few things you can try to troubleshoot the issue:
- Check the fuse: The coffee machine may have a fuse that has blown, causing the machine to stop working. Check the fuse and replace it if necessary.
- Check the power cord: Make sure the power cord is securely plugged into the coffee machine and into the wall outlet. Check for any visible damage to the cord, such as fraying or cuts, and replace the cord if necessary.
- Check the power switch: The power switch may be faulty or not functioning properly. You can try to clean the switch or test it with a multimeter to see if it is working correctly.
- Check the heating element: The heating element may be faulty or not functioning properly, causing the coffee machine to not turn on. You can test the heating element with a multimeter to see if it is working correctly.
If these troubleshooting steps do not resolve the issue, it is possible that there is a problem with the internal components of the coffee machine. In this case, it is recommended to bring the coffee machine to a professional repair service for further diagnosis and repair.
How do you fill the water tank for the scm630wc?
Grab the handle of the tank and pull forward. Then lift the tank out of the housing. At the sink, turn the tank upside down and twist off the cap by turning counter-clockwise. Fill the tank with cool tap water. Then replace the cap firmly. Return the tank to the housing using the locating tab on the tank base to easily align the tank with the humidifier.
See the manual at ManualsLib here:
https://www.manualslib.com/manual/1041172/Sunbeam-Scm630.html?page=2 . (I found the Show simplified version button helpful.)
I hope this helps.
Cindy Wells
Grohe Red Duo M not working suddenly
Grohe Red Duo M is a two handle kitchen faucet that was recently installed in my home. A few days ago, one of the handles suddenly stopped working. I have tried everything to get it to work, but it seems to be completely nonfunctional. I am not sure what could have gone wrong, as the faucet seemed to be working perfectly fine when it was first installed. I am now at a loss as to what to do about this problem.
Not finding what you are looking for?