2-Way Remote Starter - Answered Questions & Fixed issues

why don't u try online websites.. some websites deal in it real time. . along with solutions to problems how to repair fix service nd all let me know if u need help I know plenty

hello u will find a lot of wiring diagrams, codes etc and circuit diagrams help books and stuff like this at online places.. like reliable-store for free the girl in the chat box can help u instantly... im a frequent buyer there since Im a mechanic so take help from there

May be check the battery terminals to see if they are dirty or loose... & check the water level in the battery to see if theres any there At all??

You did not mention the details of your vehicle but the most likely cause is not having a bypass module installed with the remote starter. The reason you may need a bypass module is to replicate the function of the chip that is imbedded in your key.

If you are a professional installer then there are numerous technical support sights to access the wiring diagrams for the vehicle. However, what you really should be worried about is the EVO- ALL and how it connects to the Crimestopper unit that you are using. You have to be certain that the hardware and firmware versions are up to date on the EVO. You can find this by examining the label on the EVO unit and, the installation manual that lists the required versions for the vehicle.

get the manuals for your car starter this should have instructions for programming another remote

from http://www.crimestopper.com/techweb/InstructionBooks/RemoteStart/rs1300dp_1304dp_a_ops.pdf Note: All transmitter codes must be learned at time of programming!! The unit will learns up to 4 different transmitter codes. 1. Open Hood (If no hood pin installed with your system, then you must ground the Gray Hood pin wire). 2. Turn key to the ON position. (Pink wire must be connected.) 3. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. 4. Press button #1 of the transmitter to be coded. You should get 2 light flashes indicating the unit is waiting for a 2nd code, then press button #1 of a second transmitter, the unit will flash 3 times indicating its waiting for the 3rd code and so on. If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise turn key off and close hood. See diagram below.

Have you check the batteries?

I need to reprogram my chx433tx remote

Either hit lock then the start button once if that doesnt work Hit lock and then start button 2x.

you have to get the exact remote as your old remote and it will tell you how to program it

see dealer if stock, if not stock., contact the maker of the RADIO.most radios are set to no code. (new)if PO (prev.owner or kids) set it. then you must guess it.there is no secret bypass. (not public,) RTM it says just that.if you could bypass it, radio thefts would skyrocket.At some dealers, they do have a fix but you just show up with registration in and match your drivers license. or no dice.

Ebay has the Remotes

the problem with this remote is that it is used for a bunch of different models you have to look under the dash and get your unit model number and then check the crime stopper manuals for that units number you do this at www.crimestopper.com under support tab click on manuals and manuals again and then choose the model number you found under your dash

you need an ignition by-pass modual to go with the cool start modual (there sold seperatly)

Most likely you will not be able to. Most jurisdiction have restrictions on how long you can run for.

Best bet to find out the options available on your model for run time would be to contact Crimestopper and ask them, or visit your local Car Stereo/Starter specialist and have them check it out.

www.crimestopper.com

you may have bad solder connections in the remote.

Hi Sandra!

Without knowing exactly which model you have, try this website:
http://auto.manualsonline.com/manuals/mfg/crimestopper_security_products/crimestopper_security_products_automobile_alarm_product_list.html

Hope this helps.

Hi

you only need to replace batteries
it is just fine

You need to hook up the disarm wire also and depend of what car you're working on, it will disarm when you unlock the car.