20 Most Recent Invacare Pronto M51 Power Wheelchair - Page 5 Questions & Answers

0helpful
1answer

I have a Invacare Pronto M51, the chair won't move. When I turn on the joystick, the wrench light flashes 9 times, stops, then flashes 9 times again. Can you tell me what that indicates?

A flash code of 9 indicates a communication fault. What this means is that there is a lack of communication between the joystick and the other electronic component, the controller module. In my experience, the usual culprit is that the charger plug makes bad contact inside the joystick housing causing it to heat up and burn. This can cause components inside the joystick to burn out. The other more common problem is that there is a break in the 4 wire harness going from the joystick down to the controller in the base. Sometimes it is just a matter of unplugging the connector, cleaning it, and pushing it back in. In other cases, the wire has been cut or broken along its length. Look for cuts along the black covering of the 4 wire harness (connecting cable)and twist and tape or splice and solder to repair the wires. These connecting harnesses are so inexpensive it is usually easier to replace, however a quick splice can get you going temporarily. If you smelled burning that would be an indication that the joystick assembly has burned out and I would replace that along with a new harness (connecting cable with a plug on each end) to the base electronic module. The connecting cables have always been a weak link in this design and have had a history of failures over the years. For this reason I replace both the joystick assembly and connecting cable when servicing. Hope this helps.
3/22/2014 12:11:28 AM • Invacare Pronto... • Answered on Mar 22, 2014
0helpful
1answer

How do I adjust the seat height on a Pronto M51 with SPJ+ Joystick

The seat height can be adjusted by removing the seat and raising up the 4 seat pillars on the bottom frame. With the pivot seat model you can raise the center post seat pillar.
3/6/2014 1:53:05 AM • Invacare Pronto... • Answered on Mar 06, 2014
0answers
0helpful
1answer

Owners manual

hmmm type in name of chair pluss model slash manual should bring it up
1/20/2014 4:32:18 AM • Invacare Pronto... • Answered on Jan 20, 2014
0helpful
1answer

WHEN TRYING TO CHARGE POWER CHAIR DO U HAVE TO LEAVE THE START SWITCH ON TOO CHARGEpronto sure step

no u do not turning it off is better
1/20/2014 4:30:40 AM • Invacare Pronto... • Answered on Jan 20, 2014
0helpful
1answer

E100 error code

that should be a general fault,please contact your dealer
1/19/2014 3:54:12 AM • Invacare Pronto... • Answered on Jan 19, 2014
0helpful
1answer

Battery level indicator fluxuiates

some how u have a loose connection on the battery cables im thinking,check there first then all connections to joystick
1/19/2014 2:54:06 AM • Invacare Pronto... • Answered on Jan 19, 2014
0helpful
1answer

Chair has power but when activate toggle it does not move

hmm check levers under your seat make sure they are engaged or press horn 2 times within ten seconds to unlock the joystick
1/19/2014 2:22:35 AM • Invacare Pronto... • Answered on Jan 19, 2014
0helpful
1answer

When i turn the power on the lights come on ( on

wrench flashes 9 times
1/1/2014 9:41:29 PM • Invacare Pronto... • Answered on Jan 01, 2014
Not finding what you are looking for?
Invacare Pronto M51 Power Wheelchair Logo

300 questions posted

Ask a Question

Usually answered in minutes!

Top Invacare Health & Beauty Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Rob Hill
Rob Hill

Level 3 Expert

1480 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66919 Answers

Are you an Invacare Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Invacare Health & Beauty

  • Invacare Health & Beauty

Most Popular Question

invacare m51 surestep new batteries will

  • Health & Beauty
Loading...