NorStar T7208 Corded Phone - Answered Questions & Fixed issues

It's not so much removing Denied in Admin as it is enabling whatever feature the user was trying to access at that set. Which was... ?

usually the admin password is left at admin (23646)

It\'s the button above the hold key. It looks like a globe or a picture of Saturn.

You have to have two lines coming into the phone to have separate lines. Call the phone company.

This requires a programming change that has to be done on a M7310 or M7324 phone by someone that understands programming.

If there is another phone that this doesn't happen on, try changing your handset with that one. If this doesn't fix the problem it most likely is your telephone.

The digit "1" might be sticky or defective on the key pad -If sticky then try to wiggle digit "1" free or spray a proper computer contact cleanser around it and wiggle it around, all while holding the phone up and down so the run off does not go onto the motherboard.-If defective call your local vendor/tech to have it replaced with a refurbished setYou could try to unplug the phone for a few seconds then plug it back in and wait for it to boot up.

From installer programming under Restrictions and Permissions. It's a table that, if you get access to it, you can change the program. It's system wide, or part of Class of Service. Tough to be specific on an open forum. Whoever set the phone system up should be the one to change it.Carl

I forgot nokia 2626 security code. How can i retrieve it?.imei no. 359335022916297

MASTER RESET OF NOKIA 2626 SECURITY CODE

It is on of the keys on the side. The 8 keys from top to bottom are: Copy/Yes Backspace/No Change/Remove Add/Default Heading/Retry Show/<-- View --> Back Next/Ok
Excerpt from the 7208 Programming Overlay

Hi,

Remove battery and disconnect connection.
1)Put the phone into dialing mode by either picking up the handset or turning it on to speakerphone mode.
2)Dial "**RENEW" followed by the MAC address.
3)Wait for the tone to confirm that the reset was complete.

Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thank you for using fixya have a nice day:-)

To chane the name on the sets you'll need to enter telephone programming.
Programming is done on 7310, 7324 and 7316 type sets.
Enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the show key (top right arrow).
The display should now ask for an extension number.
Enter extension number you want to change the name on.
Press the show key (top right arrow)
The display should say LINE ACCESS
Press the next key (bottom right arrow) .
The display should say CAPABILITIES.
Press the next key (bottom right arrow) .
The display say Name.
press the Chng soft key.
use the dial pad to enter the name. advance using the arrow soft key to go to the next letter
ex. Bill = 2,2 -> 4,4,4 -> 5,5,5 -> 5,5,5
Press the next key (bottom right arrow) to enter the name.
Press the release key when finished

Sounds like your transfer and pick up button are actually direct inward dial (DID) lines. To see whats programmed under those buttons, press feature *0 then press your transfer button. It will probably give you a line number and port assignment for the line.

On the colleagues phone, press feature #65.

put your first caller on hold.
dial your second call, press conference
then press the first call that is on hold.

The feature is called "Call Forward/No Answer" - the procedure is in the Norstar System manual.

Try this:
Press "Feature (star) (star) T I M E"
and follow the display prompts.
Good Luck!

Hi The code you need is Feature *1 for external calls, Feature *2 for internal calls Feature *3 for functions.

F*4 is 'Call Forward'

If you Press Feature *0 then press each button in turn it will show you what is under that key (Button)

If you are setting up external calls you may have to pre-fix every No; with a 9 . if you are in 'Pool Group' working.

Hope this helps

to reset the administrator pasword enter feature 985 press 9, at the password prompt enter 73738767793 (resetsmpwsd) and press ok or #,press yes to reset password. password should be defaulted to 0000. then try Feature 983. if your system has 2 digit intercom #s your password is 120000.

To reset your voice mail password, press feature 983 the screen should say log:
enter 1020000 (default password) if you have a 3 digit intercom number, 120000 if you have a 2 digit intercom number
the display should say mbox, AA, and othr above the three soft keys
press the mbox soft key
the screen should say add, del, and chng above the soft keys
press the chng soft key
enter in the mailbox number you wish to reset the password on
press ok
the screen should say reset and next above the soft keys
press the reset soft key
press the Rls key
your password should be reset to 0000