Where do I place the jumper to set a maxtor model 31024H1 to run as slave?
Support can be found at Seagate.com in case this is not the exact drive. The model number you listed was not an exact match.
Posted on Nov 25, 2007
I have data on a Maxtor hard drive, Model 87000D8 that I need to retrieve, I want to slave it in and then I can recover the data.
I need to know the jumper settings for this hard drive.
Thank You.
I have the same situation as described by Pld8457. The Maxtor drive is Model 90845D4. Manufacturing P/N D8197-60101, Replacement: D8197-63001 and Exchange D8197-69001. (this is from the hard drive label)
Jumper J48 and "cable select" on.
Here's the chart that lists the jumper settings for all of the various models of Maxtor hard drives:
http://www.seagate.com/images/support/en/us/mxo_ata_jumpers.gif
The first drive above is a DiamondMax 1750, and
the 2nd is a DiamondMax 4320
Posted on Feb 08, 2008
need jumper settings for maxtor hard drive,,model 91362u3,,13 gb,,want to make slave out of it
no jumpers = slave
FAQ here
http://seagate.custhelp.com/cgi-bin/seagate.cfg/php/enduser/std_adp.php?p_faqid=341&p_created=985649154
Posted on May 26, 2008
I have miss placed my power pack for my Maxtor 500GB external hard drive
500GB PN 9NZ2A4-500
Is te power supply 12 volts dc and what is the polarity
Are manuals available for this hard drive
My address is, [email protected]
The PSU for my Maxtor 500Gb 9NZ2A4-500 drive is 12V DC, 2A rating, 2.1mm "plug" with centre "hole" as positive.
Regards, kbsguru
Posted on Nov 24, 2008
jumper setting for maxtor n256 diamondmax vl 40 5400 rpm
There is usually a diagram on the drive showing the jumper configuration.
Posted on Mar 16, 2009
what are the jumper settings for a Maxtor model 96147h6
try this
Posted on Jul 14, 2009
5T020h2 jumper setup
No jumper is used on the J50 pins, when using the Maxtor 5T020H2 IDE harddrive, as a Slave harddrive.
In otherwords do not use a jumper on any of the jumper pins.
This is a PDF file of the Harddrive Specifications of the 5T020H2, 5T010H1, 5T030H3, 5T040H4, and 5T060H6 Maxtor IDE harddrives,
from Seagate. (Seagate bought out Maxtor)
http://www.seagate.com/staticfiles/maxtor/en_us/documentation/manuals/dm_plus_60_ultra_ata_manual.pdf
The Jumper Settings are in Chapter 2, Page 5 (2-5)
Looking at the page number for the PDF file it's on Page 15.
Posted on Oct 09, 2009
maxtor n256 model 90510D4
jumper settings
Check this diagram. it shows all configuration in detail..
good luck!!
Posted on Jan 02, 2010
Slave jumper settings for a Maxtor N256 Hard Drive
I have never personally seen one but most drives are the same for the type of jumpers installed. See if this helps you:
http://eshop.macsales.com/Tech/manuals/idehdsettings/Maxtor72.pdf
Posted on Apr 28, 2010
need the jumper settings for the maxtor 40GB model 5T040H4 just need the slave jumper settings
see the picture below for jumper setting
Posted on Nov 26, 2010
805 questions posted
Usually answered in minutes!
421 Questions
140 Questions