20 Most Recent Craftsman 17.5 hp 42 in. Deck Lawn Tractor - CA Model - Page 7 Questions & Answers

From https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=7&cad=rja&uact=8&ved=0CFYQFjAG&url=http%3A%2F%2Fwww.ssbtractor.com%2Fwwwboard%2Fview_all.cgi%3Fbd%3Dlawn%26msg%3D34637&ei=XcwWVKuIKNj_yQS01IHQCw&usg=AFQjCNFCo3lL2R0_E1Lfi7lI7t-JML2opA&sig2=JmZgmFbwN7JLNomAb0O4XA Torque Head Bolts Since I do not have a way to send you a picture, I will describe the sequence. With the cylinder head in a position where there are two holes on your left and an open, blank, space on your right in the vertical surfaces (you might want to make a sketch of this) - I will give the sequence going in a clockwise direction. The open blank space I refer to is in the pushrod gallery area. No. 1 is in the center of the side closest to you. Number the holes 1 thru 7 going clockwise. Tightening sequence - 1, 3, 6, 8, 5, 2, 4, 7. Torque to 220 inch lbs. Tighten first round to 75 inch lbs next step to 150 inch lbs next to 200 inch lbs, then final step to 220 inch lbs. and recheck. Tighten all bolts in sequence to whatever figure you are using.

Yes it could be valves. I will need to know the make, model and serial number of engine. On Briggs and Stratton engines these numbers are typically on the top of the valve cover or on the very front hidden just under engine shroud. It may read model, type/code. If its a Kohler it will read family, serial, etc. If you can provide these numbers I can help. I’m happy to assist further over the phone at https://www.6ya.com/expert/layne_0fccff498c319c32

check this out. should at least be similar to yours. to be exact, you would need the model number from the engine. https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=4&cad=rja&uact=8&ved=0CD0QtwIwAw&url=http%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DNjzX-PUjKmo&ei=OvIRVL3xBqrCsASo4YHwDQ&usg=AFQjCNH9orjfy_J4Jv6G-FOpJkdgs1CYzw&sig2=_apKzP-s_vF4xJNuhBmnlQ

usually on a tag on the rear body under the seat.

need to adjust deck side to side height and front to back height. this is usually in the owners manual. just search for your model number and you should be able to find it. if you cant, let me know and i will see if i can.

I need the model number of the engine for this.

http://www.manualslib.com/manual/518759/Craftsman-247-288812.html page 32. strictly a parts breakdown, but I believe the lever goes directly to the transaxle.

If you are saying that it turns easier or faster to the left than to the right, most likely you have a problem with either the linkage or possibly the front axle beam itself.

You can go to www.murray.com , enter your model number and download an owners manual which will have the instructions and diagram on how to do it

Most valve clearances for b&s are about a sheet of papers thickness. If you would like exact measurement, get me the model number of the engine and I will attempt to find it for you.

at the sears parts website. They usually have them for sale or as .pdf files. you will need to know the sears model number. http://parts.sears.com/partsdirect/index.action

you should see at least 60 psi but 90 is better... do to the compression release mechanism if the engine cranks slow you might not see anything above 60...

model number

model number would get you a good answer...

My Craftsman engine leaked gas out the breather when the float in the carb was stuck so it would not close properly. The pin that held it in place came out on one side so the float would not work properly.

May I get the make and model # to get you the right belt diagram

Can you expand on this? are you not able to drive? fwd/backword? Does engine die when you put into gear?

It's not getting fuel thru the carberator another solution is the needle is stuck sometimes after it sets over the winter the needle ( which has a rubber end ) sticks closed

Some mowers will not allow you to shift into reverse with the blades engaged for safety reasons. Try disengaging the blades then shift into reverse.

Not sure where to get compression pounds for this, but let me refer you to the Briggs website for detailed product specs and power curves. Intek can be twin or single sylinder. For Twin.... http://www.briggsandstratton.com/us/en/engines/rider-mower-engines/intek-series-v-twin For single....the are in 1/2 HP ratings but the link is below.... http://www.briggsandstratton.com/us/en/engines/rider-mower-engines/intek-with-xrd-single-cylinder If further detail is required, I will need the model type and trim found on the valve cover.