20 Most Recent
Lisle Serpentine Belt Tool & Accessories - Expanded Model - Page 4 Questions & Answers
Bosch aquatak 1200 plus
2 from the power cable and 2 that goes to the commutator circuit of the motor inbetween is the switch placed there can be a capacitor parrallell placed on the wires for suppression on the commutator side.
10/30/2016 11:54:50 AM •
Hammering
•
Answered
on Oct 30, 2016
Bosch jackhammer
To long without service , or problem with a broken part ? or an problem with a electric field (slide contact somewhere ) or one of the carbon brushes is autostop activated ?
Or simple a cable break , a switch with a problem ,
9/12/2016 1:16:05 PM •
Hammering
•
Answered
on Sep 12, 2016
My Jackhammer starts for a good 5 seconds then stops but continues to make a humming sound. Can you tell me what could be wrong
Sound like a bearing problem the armature (if electric) then it could also then touches the metal of the electric field. so the armature is not in balance in the middle or the field is become loose by the vibration he then drags on the field and then there is no induction anymore. it adheres magnetically with a good humming , it is not the capacitor because there is a start direction every time so when lubrication is necessary then allways use all rings to replace because it has no target to replace one ring and it are different rings also different materials choiced on acid temperature dissipation material on any place could be different The front may have leaking air specially on the battle bolt . The right grease for a slow rpm hammer or special oil for the high rpm hammer.
9/12/2016 1:06:22 PM •
Hammering
•
Answered
on Sep 12, 2016
My jackhammer stoped hammering please help
if the internal motor still runs , but the chisel doesn't move , this is a sure sign that the drive pin has broken off , un plug and remove lower part of tool , there just after the motor shaft is a flat gear looking item , it has a pin sticking out of it bottom side , except I bet yours doesn't have it sticking out any longer , this pin will need replaced , this occurs when operator gets tool stuck in hole and pulls back while running it , ive changed a few in years past
8/5/2016 8:08:12 PM •
Hammering
•
Answered
on Aug 05, 2016
I cant find kango oil
What kango hammer do you have? I am most familiar with the UK kango 900 and 950, pre-milwaukee.
7/5/2016 4:20:03 PM •
Hammering
•
Answered
on Jul 05, 2016
Aeg ph26 drill
Inside a mechanical problem by the switch or other problem of a broken piece ring in front of the locking sleeve where the impact bolt fits the chisel.
Milwaukee PH26 or AEg PHE26
6/29/2016 4:19:15 PM •
Hammering
•
Answered
on Jun 29, 2016
Where do I put the oil?
Most breaker hammers have no oil if they have no high speed.
But special grease with high thermal conductivity.
very important .
If there is loose grease buy a consumables kit only complete , only then it makes sense.
6/29/2016 3:57:27 PM •
Hammering
•
Answered
on Jun 29, 2016
My kango 637 breaker runs but no power is getting to the chisel canyou help please
There are a couple of main things that could cause this. Unfortunately this is an obsolete machine and I doubt you will be able to find any spares for it. Probable causes are worn seals/in need of service. Worn armature pinion gear and/or crank pinion gear. Ideally you should replace both if either one is damaged, even if the other one looks ok. There are always other possibilities but they it would need stripping on the hammer mech to check all the piston/pins/anvils etc. This is a very old machine (I cut my teeth on these when i started in the trade 20yrs ago).
5/18/2016 5:05:32 PM •
Hammering
•
Answered
on May 18, 2016
Armature for kango 950 240
Unfortunately, Kango is gone - there are very few parts available and most of the parts still around will only be found in Europe now. It really is too bad because they were a great hammer.
3/29/2016 5:51:19 PM •
Hammering
•
Answered
on Mar 29, 2016
Bosch jackhammer
broken power cable or autostop inside the carbon brush they are short its time for a revision !!
3/26/2016 12:50:02 PM •
Hammering
•
Answered
on Mar 26, 2016
Not finding what you are looking for?