20 Most Recent Price Pfister Marielle Kitchen Faucet with Matching Spray and Soap ... - Page 2 Questions & Answers

Have you tried Lowes or Home depot for the replacement part if they do not have it.You need to check out a plumbing store.Hope this helps

Unscrew top button. Using a phillips screw driver remove handle retaining screw and work off handle.If it leaks under the handle you need to unscrew the top cap, use a strap wrench to hold the body and tighten the brass retainer ring with an adjustable wrench. Or remove the ring to replace the cartridge.

Pop off the cap on top of the faucet, unscrew the philips head screw,pull faucet up and off the brass center and replace the two o-rings you see .

It is screwed in. You have to remove the head on the spray, then remove the faucet.

try un-screwing the screen on the end where the water comes out. Could be clogged

wow need a new faucet?? NO just kidding

Ok the water not running out of the faucet. that is the screen on the end of the spout, just un screw it clean it and your good to go.The leak on the spray, pull the spray out and run it and look at the connection right there on the handle.

if there is no leak, get an other person to run the sprayer and you take a flash light and look up at the bottom of the faucet.and see if you can see the leak from there. The hose should attach to a brass section coming out of the bottom of the facucet, It may be it just got loose and you need to re tighen it. Now yo will need a basin wrench to do that . If yo dont have you you can buy a cheap on ( which is all you need) from a hardware store,

Also if you take your hand and feel around the the bottom of the sink where all the pipe come down it might be the fauect itself.

Good hunting be safe protect your eye

Tom

no you have to take the sprayer all the way off and replace the broken coupling

Sorry we could not give you a quick fix

Tom

Yes I can tell you, there is a fitting inside the faucet its call a divertor. When you use the spray handle it clicks over and makes all the water that was going to the spout go to the spray handle.

If you did not have this jsut think how it would work with half the water going to rach side. I don;t know how old your fixture is but it may just have gotten some lime or and other drop of trash inside the faucet.

Turn the water on cold only open full, kinda rapid fire the trigger to make the water jump back and forth for about 3 mins. This may jar lose the junk and stop it from doing what it is doing. If that does not fix it the faucet needs service

best of luck

Tom

The hose that goes to the Sprayer has to be disconnected under the sink at the main connection there, then it can be pulled up and out of the top of sink. the you can unscrew the nut under the sink on the flange and remove and replace.

Yes it can. Just contact Price Pfister through their website and order the parts.

I would try replacing the cartridge. Handle has a set screw (probably an allen head) There should be a retaining nut holding the cartridge in. Unscrew it and pull the old cartridge out. You might have to pull pretty hard.

Hi,
The passageways in the diverter part of the faucet are very small and can get dirt stuck in them....the diverter is a plunger like piece that will slide and stop the faucet when it senses flow from the sprayer...
The only hope of cleaning this out is to do this...
Take off the supply tubes or pipes at the hot and cold supplies... then blow compressed air....a air compressor with 100 psi air and a blow gun works best...backwards through the hose and out the supply tubes....this should blow out any built up dirt in there and get the passageway open again...you also could try to open the faucet valves... take the aerator off the spout and try to blow through there also... just in case there is build up in there also...

heatman101

Clean the tube too.Also make sure there is no debris in the bottom of the caister.

Most parts can be ordered though Price Pfister Directly 1-800-PFaucet. Here is a link to the parts diagram for your faucet. http://www.pricepfister.com/www/ImageAssets/mirror/model/kitchen/treviso/tret26-4d/ex-026-02.pdf  If by threaded shank you are talking about the bottle, then you can order just a new bottle (Part # 950-004) if not you may need to order a whole new soap dispenser (Part # 920-054.) If you order a whole new soap dispenser than make sure you order the correct finish to match your faucet. 

Above I included the steps for you to change your cartridge

Master Tech Plumbing 5150 Interstate 70 Dr SW, Columbia, MO 65203 (573) 777-7777 Website

• Directions
• Send to mobile

That faucet was discontinued some time back for the one you ordered parts for and the only way to get the part if it is still available is to know the part number. Now if you have a plumbing parts house in your area that specializes in faucet parts they may be able to match up the old part if you still have it.
If you can find the part number for the faucet you have then the part may still be available from Price Pfister.

Might need to replace the gasket. Unscrew the tip check and replace gasket clean the area with soap and old tooth brush.

Remove the retaining nut under that should be a fitting with a small horse shoe shaped retainer chip. Remove that wit small sharp tool maybe a small mini screw driver and and it will come right off.

I am not sure which facet you have. Please review the web link below. I hope this helps you...Jim

http://www.plumbingsupply.com/pp-kitchen-faucet-repairparts-marielle.html