20 Most Recent American Standard Colony 3275.505 099 Chrome/Brass Mixage Soft Two-Handle B... - Page 4 Questions & Answers

You will need to take those old parts to a store or place that handles Danco replacement parts. I wish I could direct you to a place that would have what your looking for but parts that old are just not out there. The other possibility is to rebuild what you have those old parts a really tough. I have some old stems and handles that you are welcome to just send me some pictures of what you have and we might get lucky. [email protected]

If you live in an area where it freezes for long periods of time in the winter you should put in footers at a 3 to 4 feet and even if you don't live in freeze area you should put in footers at a 1 1/2 to two feet if want the porch, As for the 3" you may as well go with what ever a 2x4 comes to and you will not have to cut the boards dow to 3".

Some seats ae rremovable and some or not Some take a hex(allen) wrench and some take a square (seat removal tool)  Most of us use a seat grinder. (another tool to dress up the seat (Remove material) past the seat damage. You will find any of these tools at any hardware store that sells plumbing parts. If the seats have a square or hex hole remove and replace rather that grind(dress)the seat. All right hand threads meaning turn counter clock wise to remove. Take old seat to the American Standard plmbing supply outlet and then will match it up. Good fix-in to ya.

Hi, Bro..
Please get it here, then www.concrete-pipe.org/pdfs1/DD_1.pdf
www.concrete-pipe.org/pdfs1/DD_3M.pdf
www.concretepipe-mi.org/pdf/resource_catalog_06-07.pdf
I hope you will the pipes master after get these stuffs.
Best regards, Jay

(1/3) x pi x radius2 x height x density = pounds

where ::


radius = radius of base in inches

density = pounds per cubic inch

height = height in inches

(or you could use feet, meters, cm, mm for radius & height and use kg for density or wahtever units you wish as long as the units are consistent)

Charlie

bdujwu7ye je9809 l,ldchr fk;lkjf

Check the screen in the end where the water come out it could be plugged.

http://www.jadousa.com/products/productDetail.aspx?id=3582

exploded diagrams:
http://www.jadousa.com/assets/documents/jado/parts/Parts_3794.pdf

"deep six" it
American Standard brass is ****!

Unscrew the pop-up cable connector from the drain tail-piece and rotate the screw on the side 180 degrees. Reattach the cable adapter.

Hi Tom. Get a set of allen wrenches, insert one after another into the hole until one catches on that allen screw. You could also get a small mirror and a flashlight and look into the hole. I can assure you that there is an allen screw in there. It is just a matter of finding the correct allen wrench and getting it seated into the allen screw.

Go to this link http://www.ehow.com/how_4896394_remove-american-standard-ball-faucet.html
to see the step by step instructions

Joe
Thanks for choosing Fixya!

try reversing your hot and cold lines

Tub spout threads onto end of pipe. The diverter does not play a role.

Sometimes these things get rusted in place, and you have to bend them getting it off.
When all else fails, get a big pipe wrench and muscle it until it bends up and comes off.
Sounds like you might need a new tub spout ... and might need a new pipe ... be sure to match length of pipe to depth of threads on new spout.

Photos from google-image search for "tub spout removal tool"
http://www.justingermino.com/replacing-bath-tub-spout/

Howdy. We are FixYa.com and I am Farmerbear. How can we help you today?

Replacing the spray diverter or faucet cartridge ( depending on your model) will fix the problem. Call American Standard and ask for free replacement parts.

Chisel notch on inside of drain away from tub & hit it counter clockwise until it unthreads from lower section.

don't we all !!!

??? please explain!!

it is called hydraulic hammer nd meant that you have very good pressure in your lanes, if it start suddenly, this meant that your air chamber lost it's air, in that case simplest solution will be as follows:

1. close the mains,
2. open all taps (fawcets) and drain all water from the system,
3. close all taps (fawcets)
4. open mains and check if hammer is still present.

if hammer is still present, that meant you need to clean your airchamber, you need to find where it is lockated, follow steps 1 and 2, open airchamber, check if any debris inside and clean, re-seal the chamber, then follow steps 3 and 4.

if hammer was always, this meant that you do not even have airchamber. you can install one easy for yourself, just purchase one, and best place for it is on the end of the line, somehere close to most offending faucet.

if you find this advice helpfu, please do not hesitate leave your remark and give me your vote, thanx!

So are you going to build your own? Is it going to be for cold water only? Cheaper to buy a safe manufactured one. And a bladder tank is even better : Shell thickness: The minimum thickness
of a shell shall be determined using the
following equation:
Ts = PR/ES
E = Weld efficiency for longitudinal welds
(0.85).
NOTE: E = 1 if 100% of production
is tested at the maximum
working pressure.
S = Yield strength 20,000 psi
(140,000 KpA) or greater if certified
by the manufacturer.
See this link. http://www.watersystemscouncil.org/VAiWebDocs/standards_docs/ANSI_Final_0905.pdf

hi, sorry no answers for your homework but check out this link and the example at the bottom of the page is what you need
http://www.coilgun.info/theoryinductors/dampedoscillator.htm
hope this helps