Top 20 Lexmark X4650 InkJet Printer - Page 9 Questions & Answers

The following may work: remove all the ink supplies. Remove the printhead and soak it for about 5 minutes in 0.5" of very hot water. Gently blot the printhead on a soft damp paper towel to remove the excess water, then replace in the printer and then reinstall the ink supplies.

You seem to have done most troubleshooting steps for this kind of problem. Try to make sure that the paper guides rests on the side of your paper in the feeder to properly secure sheets when fed.

That could be a spooler problem. Make sure the print spooler service on your Windows computer is running. (How to Restart or Reset the Print Spooler in Windows). After following the steps in the article, try to print again.

Your cartridges probably needs cleaning. On the printer operator panel, press Setup button -> Maintenance -> Clean Cartridge. Your printer will then print a test page, forcing ink through the nozzles to clean dirts and possible clogs. You may also try to re-seat your cartridges. Or insert a different know good cartridge to determine if it's a faulty cartridge issue.

Make sure the printer is on. Open the printer cover and press the lid to open the cartridge holder.

If you have lost the disk you can download it from Lexmark website.
http://support.lexmark.com/index?locale=en&page=product&productCode=LEXMARK_X4650&segment=SUPPORT&userlocale=EN_UK&frompage=null#1

First you want to make sure your printer has wireless capability. If yes, you want to make sure wireless is turned on. Log into your wireless router, and go DHCP section to find out what IP that assigned to printer. Once you know the IP, you can change the port of printer to that IP via control panel and printers and faxes. Good luck and let me know if need additional help.

remove the cartridge and clean all the contact points on it (not the ink spitting part) and reinsrt it. Use a q-tip and rubbing alcohol.

For scanning your documents or you letters, you will need the OCR software that is available only in the install disc for your printer. Please contact Lexmark technical support for assistance on this matter.

Sometimes the ink cartridge carrier won't automatically move to its loading position even when the printer is on and the cover is open. Follow the steps below:

1. Unplug the printer from the power source.

2. With the cover open, hold the solid white strip that connects from the carrier assembly to the ink cartridge carrier and gently slide the cartridge carrier to the center of the printer.

3. Remove the used cartridges.

4. Load the new cartridges. Close the cover.

5. Plug the printer back to the power source.

JUST GO TO THE LEXMARK SITE AND U GET ALL DRIVERS FOR FREE,JUST DOWNLOAD

Try to reset your printer to factory default settings. On the printer operator panel, press the Setup button -> Defaults -> Set Default -> Use Factory. You will be prompted to enter the date and time, etc. Then power cycle your printer. Remove the power adapter from the printer.



Wait at least 10 seconds before replugging the power adapter.

When your printer turns on, check if it's properly working now. If problem continues, please contact Lexmark technical support for additional assistance.

Try to clean the cartridge nozzles. On your printer operator panel, press Setup button, press Ok -> Press the arrow buttons until Clean Cartridges appears, and then press Ok. A page prints, forcing ink through the print cartridge nozzles to clean them. Try to print your document again.

If you're having a hardware problem where the printer has become inoperative, I would strongly suggest you to contact Lexmark technical support for assistance.

If you're asking if the Lexmark X4650 supports spanish language, yes. You can set the printer language by pressing the Setup button -> Device Setup -> Language -> select Español -> press Ok button.

The Lexmark manual says: Remove the tape from the back and bottom of the color cartridge, insert the cartridge in the right carrier, and then close the color cartridge carrier lid. See pic below...

try : release and after config new - by a command line

You will need to use the Lexmark X4650 driver for Windows 7 64-bit from the Lexmark website. First, uninstall the existing driver from your pc. Go to Start menu -> Programs -> Lexmark 4600 Series -> Tools -> Uninstall. Reboot your pc when prompted.
To reinstall, click on this link Lexmark X4650 Driver for Windows 7 64-bit. Download, execute the file and follow the instructions on the software.
I hope this information has been helpful. Thanks.

http://www.lexmark.co.uk/lexmark/sequentialem/home/0,6959,252735_1255995709_0_en,00.html
try and download one here
hope this helps

Please get it downloaded at : www.nodevice.com/driver/company/Lexmark/Printer.html
www.lexmark.com/
www.driverslab.com/drivers/Printer/Lexmark/9/63.html
Regards