20 Most Recent Lexmark X4650 InkJet Printer - Page 7 Questions & Answers

It could be just a slight communication problem. A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Simply disconnect the printer from your computer. Reboot your pc. Unplug and re-plug the printer into the power source to reset it. When the printer turns on, reconnect it to your computer. Then try to print again once the computer fully recognizes the USB connection.

If that doesn't help, try the steps below:

1. Disconnect the printer from your computer.

2. Rebrick (pull out power supply, black box where the power cord is plugged in at the back of the printer, and put it back after 30 seconds).

2. On your computer, go to Control Panel > Printers and Faxes.

3. Delete the Lexmark print object.

4. Reboot your pc.

5. When your pc turns on, reconnect the printer.

6. Wait until your pc fully recognizes the USB connection. To check, go to Control Panel > Printers and Faxes. If you see a new Lexmark print object in the list, then try to print a document again to verify that the problem is fixed.

You may also try to update your printer driver by visiting the Lexmark website at http://bit.ly/iofMNC. Select your operating system, download and execute the file.

Try cleaning the mating surfaces of the cartridges with rubbing alchohol on a cue tip. If the printer was out of ink for a while the ink dries on the surface.

This could either be a slight communication problem between your printer and your computer or a communication issue between one of your cartridges and the printer. Please follow the steps below to fix the problem:

1. Reboot your computer.
2. If usb-connected, disconnect the printer from your computer.
3. Open the printer cover and remove the cartridges. Note: If the carrier does not automatically move to the center, turn off the printer/unplug the printer from the power source and then slide the carrier to the center to remove the cartridges.
4. Close the cover.
5. Rebrick the printer (pull out the power supply, black box where the power cord is plugged in at the back of the printer, and put it back after 30 seconds).
6. When the printer turns on, reinsert one cartridge first and close the cover. Check for any errors.
7. Reinsert the other cartridge and check for any errors again.
8. Replace whichever cartridge is causing the error to appear with a new cartridge or with a different known working cartridge.
9. If usb-connected, reconnect the USB cable to your computer.
10. Try to print from your computer to verify that the problem is fixed.

I hope this information has been helpful.

Make sure your Adobe application is updated.
Try to update your printer driver as well. Please visit the Lexmark website to download and install the Lexmark X4650 Printer Driver on your computer. Select your operating system > download and execute the file.
Once the update is complete, try to print a PDF file again to verify that the problem is fixed.

Hi, please try this link:
http://www.printcartridgedirect.net/2178/lexmark-x4650-driver.htm

Please select the Operating system you are using then proceed to download.

Thanks for using FixYa.

A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Reboot your pc. Unplug and re-plug the printer into the power source to reset it. When the printer turns on, try to print again to verify the connection.

Please follow the steps below:

1. On the printer operator panel, press the Setup button.
2. Select Maintenance.
3. Select Align Cartridge.

Please visit the Lexmark website to download and install the Lexmark X4650 Printer Driver for Windows 7 64-bit.

A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Simply disconnect the printer from your computer. Reboot your pc. Unplug and re-plug the printer into the power source to reset it. When the printer turns on, reconnect it to your computer. Then try to print again once the computer fully recognizes the USB connection.

If that doesn't help, try the steps below:

1. Disconnect the printer from your computer.

2. Rebrick (pull out power supply, black box where the power cord is plugged in at the back of the printer, and put it back after 30 seconds).

2. On your computer, go to Control Panel > Printers and Faxes.

3. Delete the Lexmark print object.

4. Reboot your pc.

5. When your pc turns on, reconnect the printer.

6. Wait until your pc fully recognizes the USB connection. To check, go to Control Panel > Printers and Faxes. If you see a new Lexmark print object in the list, then try to print again.

You may also try to update your printer driver by visiting the Lexmark website at http://bit.ly/iofMNC. Select your operating system, download and execute the file.

If the problem continues, please contact Lexmark Technical Support Center for additional assistance.

This would need some further troubleshooting. Please contact Lexmark Technical Support Center for additional assistance.

Great job on trying several troubleshooting steps to fix the problem. Please contact Lexmark Technical Support Center for additional assistance.

Please follow the steps below on how to change the cartridge/s on your Lexmark printer:

1. Make sure the printer is on.
2. Lift the scanner unit. The print cartridge carrier moves and stops at the loading position, unless the printer is busy.
3. Press down on the cartridge carrier latch to raise the cartridge carrier lid.
4. Remove the used print cartridge. Then insert the new cartridges.

Hey friend, you can try this one.

1. Press the power button (Which will turn off printer.)
2. Wait till flashing stops and printer is completely off.
3. Press the same button which will turn on the printer.
4. The Printer should automatically go back to printing.
5. If it does not - Manually try printing by your self.

Leading cause of paper jams is debris/foreign objects that accidentally fell into the paper feed area. Please follow steps below to fix the problem:

1. Remove the sheets of paper from the feeder.

2. Grab a flashlight and look inside the feeder for any debris or foreign objects.

3. If you're willing and physically able, you may also turn the printer over. Any debris should just freely roll out from the feeder.

4. If feeder is clear, place the printer back on the table, open the printer cover and remove the cartridges.

5. Check the cartridge area for any obstructions/debris in the cartridge carrier's path or the paper path.

6. If cartridge area is clear, close the cover.

7. Rebrick (pull out power supply, black box where the power cord is plugged in at the back of the printer, and put it back after 30 seconds).

8. When the printer turns on, reinsert the cartridges and load some paper. Try to print again.

If the problem continues, please contact Lexmark Technical Support Center for additional assistance.

A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Simply disconnect the printer from your computer. Reboot your pc. Unplug and re-plug the printer into the power source to reset it. When the printer turns on, reconnect it to your computer. Then try to print again once the computer fully recognizes the USB connection.

If that doesn't help, try the steps below:

1. Disconnect the printer from your computer.

2. Rebrick (pull out power supply, black box where the power cord is plugged in at the back of the printer, and put it back after 30 seconds).

2. On your computer, go to Control Panel > Printers and Faxes.

3. Delete the Lexmark print object.

4. Reboot your pc.

5. When your pc turns on, reconnect the printer.

6. Wait until your pc fully recognizes the USB connection. To check, go to Control Panel > Printers and Faxes. If you see a new Lexmark print object in the list again, then try to print again.

Great job on trying to reset the printer's wireless network adapter. Somehow, the printer's memory is stuck to thinking to connect to a wireless network when it's not communicating at all. Unplug the power adapter from the printer. The power adapter is the rectangular black box behind the printer where the power cord is attached. Wait at least 30 seconds before plugging back the power adapter in the printer. That should refresh itself. If wifi light won't turn on orange after the printer's on ready, reset the wireless network adapter again. Thanks.

Hi,

Go to system settings and select the 'Printer' option.

Right-click on the printer and enable the 'Use Printer Online' function.

Cancel all the printing jobs till that moment and redo the process.

Sometimes the 'Printer Offline' message occurs due to a 'Job Stuck' issue.

Check all network connections and functions.

Be sure the network interfaces work properly.

Turn the printer off and on to see whether the device is working properly.

Your firewall could be blocking the print communication. The article below will guide you on how to allow full access to all Lexmark software and printer communication processes in the program rules/permissions for your firewall.
- Communication Failure When Trying to Scan, Print, or Perform a Smart Solution Function; Firewall Possibly Blocking a Process and Preventing Communication
Hope this helps.

Hi

You need to reinstall the software on the CD that came with the printer or download and install it from here:

http://support.lexmark.com/index?productCode=LEXMARK_X4650&page=driversdownloads&linkSelected=node2%5Esubnode2&locale=EN&userlocale=EN_UK

Then save the downloaded setup files on an external hard drive ofr USB Flash drive for future reference.

I hope this helps

Did you install the drivers off the cd that came with the printer? And if so, check your drivers and make sure it shows that its there. Maybe then you could look online for a downloadable version.