Top 20
Proscan 32LA25Q 32 in. LCD TV Questions & Answers
How do I connect a WII to this TV?
plug the red and white and yellow plugs into the AV input on the back of the TV rather than the component in on the TV. (they look very similar easy to confuse)
Proscan 32la25Q Backlight not comming on
You either have a faulty backlight or one or more of the inverter transformers is bad,
a close inspection of the picture when on will show a bad tube as it will be lighter or darker than the rest,transformers may be hot to the touch
Len..
Wont turn on
If there is no standby light, it means that the main power supply regulator board to this TV, does not get AC power at all, or there is some fault with it. It will be best to contact any service technician. If
you wish to get more details, check this link.
http://electronicshelponline.blogspot.com/ Selecting the view option, either to Mosaic
/Timeslide, can be selected by the drop-down list, by the top left
of the display window, will make surf easy. You can also do a search, by type in the brand name / model
number / IC used, in the search box at the top right of the display window
My lcd tv powers screen
Try turning off and unplugging the TV for 24 hours. It could also be a power supply issue. In that case you should get it fixed or replaced.
How do i get the eye on the bottom of the tv front
U tries all tv functions buttons sides of the tv frame and it work?Remote,u alredy change it with new set battery,same result?Yes.Ur tv remote control it is dead,probally the CPU chip on the remote itself it shorted.Try website like Remotes.com to buy the tv original remote or very closed compatible one for the replacement..
I have a VIA EPIA
VIA board graphics it is not supported,not all graphics video board supported on all LCD HD tvs.
AUDIO BUT NO VIDEO
Hello,
The T-CON board is usually under a metal shield cover and sitting on the middle top section of the screen, you will see a very thin connector with VERY SMALL WIRE attached to it, be real careful when you try to remove this connector.
Make sure the number as printed on the PCB match the one you are getting, since TV can have more than one version.
As you can see, there is F1 fuse on the left side of the connector.
Check to see if you do have 12v on it and it is not blown.
I hope this will help to fix the fault.... and do take care in handling the set because it contain high voltages....
We had a trasnformer blow and our power went
It sounds like you might get lucky and have blown the in-line fuse. By lucky, I mean, it could be worse, but you need to open the tv and check for the "white/Slow Blow" fuse that connects to the power plug of the tv.
Hope this helps :)
Remote control will not work.
Hello,
Are you using the remote control that came with your "Proscan 32LA25q 32in. LCD TV"? or are you using another remote? if so - what remote? brand and model. Also if that is not the correct television please post the correct brand and model.
basic things that you can do.
1. try a new set of batteries.
2. reseat the batteries to the remote and confirm that they are inserted correct, and the right way. Also check that the battery contacts are clean, if they are not clean, clean them.
3. find the IR receiver from your TV and point the remote directly at it.
4. move closer to the television or attempt to point the remote in different parts of the tv.
The TV takes along time
Hello tcren....
Your capacitors need to be replaced. You can order them from Allied Electronics in Largo FL. There phone number is (800)433-5700. Be sure you have your model number ready so they send you the correct ones.
When they arrive unplug the TV and place TV face down, take the back off, unplug and unscrewed the board, replace the capacitors, and reassemble.
The capacitors themselves are only a couple of dollars each. Joe
Thanks for choosing Fixya!
It takes about 3o seconds before we can turn on or
Welcome to fixya
Hello
I have a solution for this
Press Ok, Accept or replay so we may get started
Your pre-solution is coming up shortly
PLEASE
REPLY OR LEAVE COMMENT TO CONFIRM YOU RECEIVED THIS EMAIL
My name is Bruce
Television won't turn on, either by remote or
The status light flashes to signal that the power source is in protected mode. This mode has been activated by the protection system of the power source this morning, when you tried for the first time to start it. It has been activated because during the night a part inside the tv has failed and has started to act as a short.
The only way to fix that is to open the tv, test the power source, identify the power rail that is down and has triggered the protection system, follow the rail and test all components that are powered by it till you find the failed one then replace it or the whole board on which is situated.
To do this requires electronics experience, if you don't have it then call someone who has it. Or take the tv to a repair shop.
Not finding what you are looking for?