20 Most Recent LG WM-2277HW Front Load Washer - Page 9 Questions & Answers

The LE error indicates that the Controller is having trouble communicating with the motor. The most common cause for this is if something gets wedged in and the drum can't turn freely. Try turning it by hand to make sure it is free. The next most common cause is if someone spins the drum moderately fast with the washer turned off. I.e. if you give it a spin to make sure their isn't a sock stuck to the drum.. To fix this, unplug the machine and turn the drum counterclockwise 4 full rotations followed by 4 rotations clockwise at low speed. Plug it back in and see if that fixes it. If that's not it, then there is a sensor called the Hall Sensor that could be the problem. I've never had to replace one of these and can't comment further. GL

That is most likely from the belt on the drum. If you want to check that though take some of the dust and see if it is gritty feeling. you can check that by putting it on something smooth and setting something hard on top of it and moving the top object around. Or pinch it between fingers etc. The motor should be brushless because it is an AC motor.

te is a error code for a bad thermister. it senses the temp of water in the tub. this needs to be replaced If you need further help, I’m available over the phone at https://www.6ya.com/expert/dude_653d05454b389bba

Service Manuals Summary F1403FDS5 try this address

I had the same error code along with the drum "freezing" up. The first unit that was delivered 2 years ago leaked water from the detergent compartment and they sent a second unit. I have only had this unit for 2 years and I am very disappointed in the LG product. LG was no help on the phone and I the only people that could service it were 45min away from were I live. I took the advice of a posting on this website that it could be a part called the sensor assembly (#6501KW2002A) and ordered it from an online electronics store (www.mcminone.com). To get to the sensor assembly, you first unplug and take off the back plate that has 4 small screws. Next, unscrew the big bolt in the middle and take off the hubcap looking part the bolt was securing. Next unclip the two sets of wires on the bottom of the circle you are looking at (the set of wires to the right are connected to the sensor assembly you want to replace). Next you will unscrew the 6 or so smaller bolts to take off the circular piece that the sensor assembly is snapped to. Take it off, unclip the old sensor assembly and clip on the new one – and reassemble. This worked perfectly for me and the part only cost $18 bucks plus shipping. When working, this product works well but I will not be purchasing any LG products in the future.

possible bad wash motor. Is it hot inside the dishwasher or is that a washer?

check the plastic/rubber connector that connects from motor to transmission it's probably broken.

Remove back cover and check for a loose nut that holds the rotor. you may have to replace the rotor( is the cover that holds the magnets). Not the stator (which is the motor.)

To get to the pump you need to remove the top plate, control panel and front cover in that order. for the front cover open the lid at the bottom left side and remove screws.

No it may get clumpy just sprinkle it in was when there is water in the basin

I would not do it very often as some of the parts inside are made od aluminium that can be corroded easily. I would stick to the normal products myself.

its happerning some time after used dry option,,,becouse this iscondensation dry systterm,,all the humidity become water power connetion getting wet,, afetr some time its will gose off....

this is not tub clean..its child lock..kindly remove child lock frist,,,

Over-sudsing is the main cause of LE error codes. Using non-HE (high efficiency) detergents or too much detergent will cause stress on the motor. In addition, detergent residue can also cause leaking and odor. Follow these steps to resolved an LE error code caused by over-sudsing.

Step 1: Unplug the washer and allow the unit to sit for 30 minutes to give the suds time to dissolve.

Step 2: Plug the washer back in and press [Power] to turn on the washer.

Step 3: Do not choose a washing cycle. Press the [Spin Speed] key until "No Spin" is selected.

Step 4: Press [Start/Pause] to begin a drain only cycle.

Step 5: After the drain only cycle has completed, remove the clothing items from the machine. Turn the power back on and select [Rinse and Spin] and then press [Start/Pause]. This will remove excess soap suds and light residue from the drum. Repeat this step until no visible suds are in the drum of the washer.

Has a large load size been used with a gentle wash setting?Gentle wash cycles such as Perm Press, Delicates, Hand Wash, and Wool/Silk should only be used for smaller loads. Because the cycles are more gentle while tumbling and spinning, too many items in the drum can register as an issue with the motor. In this instance reset the unit and run a test rinse and spin cycle.Has the washer been overloaded?Single bulky items or large loads can add extra weight to the drum and place stress on the motor. Remove some of the clothing and restart. If the issue is still present after a few items have been removed, unplug the washer for 30 minutes to allow the motor to cool and then restart the cycle.

You nay have used too much soap! Try running the washer through a short wash cycle without any clothes or soap in it to rinse it out.

Hi,

Problems with a washing machine not spinning or not draining are often interrelated..

If you are having a problem with your top load washer then check out thistip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkoutthis tip...

Front Load Washing machine not draining and or not spinning


heatman101